|
|
|
Author |
Message |
climbamt Member
Joined: 16 Sep 2012 Posts: 32 Location: Baltimore
|
Posted: Wed Mar 19, 2014 1:15 am Post subject: Stella Master Cylinder parts |
|
|
Hey,
Anybody find a rebuild kit for a Stella 2T Master Cylinder? I have looked at the major spots and did not see one. I really just need the rubber seal that the lever pushes in.
Thanks for any help/advice.
~climbamt _________________ 05 Vespa GT200
03 Genuine Stella 2T
05 Kymco People 150
03 Kymco People 50
|
|
|
Back to top |
|
 |
az_slynch Member
 Joined: 12 Sep 2012 Posts: 1766 Location: Tucson, AZ '18 Spade, '16 K-Pipe, '13 Stella 4T, '12 Yager GT200i, '81 Vespa P200e and Far Too Many Others
|
Posted: Thu Mar 20, 2014 9:49 pm Post subject: |
|
|
|
|
Back to top |
|
 |
climbamt Member
Joined: 16 Sep 2012 Posts: 32 Location: Baltimore
|
Posted: Sat Mar 22, 2014 5:09 am Post subject: |
|
|
Thanks,
I am hoping I don't have to replace the entire MC because of a $2.00 seal. After a couple of messages on Facebook, someone from Genuine is supposed to email me. I find it hard to believe they do not have a phone number or an email address on the website for help....
~climbamt _________________ 05 Vespa GT200
03 Genuine Stella 2T
05 Kymco People 150
03 Kymco People 50
|
|
|
Back to top |
|
 |
chuckklr98 Member
Joined: 19 Apr 2018 Posts: 34 Location: 70452 stella 2t
|
Posted: Mon May 14, 2018 9:56 pm Post subject: |
|
|
I cant find a rebuild kit either for an 08 stella 2t.
what the poster above sent was for an complete master cylinder, and it does not mention genuine stella at all. is it the right one ?????????
|
|
|
Back to top |
|
 |
az_slynch Member
 Joined: 12 Sep 2012 Posts: 1766 Location: Tucson, AZ '18 Spade, '16 K-Pipe, '13 Stella 4T, '12 Yager GT200i, '81 Vespa P200e and Far Too Many Others
|
Posted: Mon May 14, 2018 11:02 pm Post subject: |
|
|
chuckklr98 wrote: | I cant find a rebuild kit either for an 08 stella 2t.
what the poster above sent was for an complete master cylinder, and it does not mention genuine stella at all. is it the right one ????????? |
It is. The Stella is made by LML and is known as the Star or Belladonna to the rest of the world. The part will fit.
Here's the internals and a seal kit. The two kits are almost the cost on a new unit and the odds are that your fluid level sight glass is hazed and cracking anyway:
Inner Piston:
https://www.sip-scootershop.com/en/products/brake+piston+kit+piaggio+brake_49837200
Seal Kit:
https://www.sip-scootershop.com/en/products/gasket+set+grimeca+brake_49474800
I'd dismantle and check the bore on your original part as well before springing for repair parts. If it's rusty, you might be able to have it honed, but it's a gamble. Brakes are not worth gambling on.
EDIT: Found this link, it's in Cali so the shipping may be cheaper than from Germany:
http://scooter-speed.com/vespa-brake-master-rebuild-kit-px-grimeca-sip-a10-49474800/
NOTE: It lists Grimeca, but it will fit. If you shop around, make sure you get a kit for the later, handlebar-mounted kit instead on the early semi-hydraulic kit that mounted on the fork. _________________ At what point does a hobby become an addiction? I'm uncertain, but after the twelfth scooter, it sorta feels like the latter...
Seriously...I've lost count...
Seven mopeds ...that's still manageable...
|
|
|
Back to top |
|
 |
chuckklr98 Member
Joined: 19 Apr 2018 Posts: 34 Location: 70452 stella 2t
|
Posted: Mon May 14, 2018 11:29 pm Post subject: |
|
|
ended up just ordering a whole new master cylinder. sips wanted an 25 buck min, on a 20 buck part, than wanted 20 to ship an 1 oz part.
They way they presented it, the 20 buck seal kit, I had to buy the piston and spring too.....just to get over the 25 buck limit. $58 bucks total, and I;m not even sure it will work .
So I just ordered the whole damn thing from ScooterLounge for 173. At least I'll know that will work.
Already ordered a seal kit that somebody said would work......and it did not. 3 weeks and 20 bucks down the drain.
|
|
|
Back to top |
|
 |
chuckklr98 Member
Joined: 19 Apr 2018 Posts: 34 Location: 70452 stella 2t
|
Posted: Wed May 16, 2018 1:32 pm Post subject: |
|
|
az_slynch wrote: | chuckklr98 wrote: | I cant find a rebuild kit either for an 08 stella 2t.
what the poster above sent was for an complete master cylinder, and it does not mention genuine stella at all. is it the right one ????????? |
It is. The Stella is made by LML and is known as the Star or Belladonna to the rest of the world. The part will fit.
Here's the internals and a seal kit. The two kits are almost the cost on a new unit and the odds are that your fluid level sight glass is hazed and cracking anyway:
Inner Piston:
https://www.sip-scootershop.com/en/products/brake+piston+kit+piaggio+brake_49837200
Seal Kit:
https://www.sip-scootershop.com/en/products/gasket+set+grimeca+brake_49474800
I'd dismantle and check the bore on your original part as well before springing for repair parts. If it's rusty, you might be able to have it honed, but it's a gamble. Brakes are not worth gambling on.
EDIT: Found this link, it's in Cali so the shipping may be cheaper than from Germany:
http://scooter-speed.com/vespa-brake-master-rebuild-kit-px-grimeca-sip-a10-49474800/
NOTE: It lists Grimeca, but it will fit. If you shop around, make sure you get a kit for the later, handlebar-mounted kit instead on the early semi-hydraulic kit that mounted on the fork. |
on that site LML is not in the system. so what other model should I use? I need a throttle tube too.
|
|
|
Back to top |
|
 |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You cannot download files in this forum
|
|
Powered by phpBB © 2001, 2005 phpBB Group
All Content Copyright 2007-2011 by Modern Buddy. All Rights Reserved.
|