DIY tire install comments
Moderator: Modern Buddy Staff
-
- Member
- Posts: 139
- Joined: Mon Apr 02, 2018 12:07 am
- Location: Lower Alabama
DIY tire install comments
Buddy 125- 2008, 1,800 miles
Recently installed new Shinko 3.5-10 tires. I do my own tire installs, for my Burgman 400.
WOW. This was a PAIN (for Buddy). Hard to get old ones off, used tons of WD-40 which usually works for me.
Really hard to install new ones. Couldn't get the tires to pop. Even using medium sized air compressor, which is my last resort usually.
Had to take to a tire shop. They must have had a tough time too, there was soapy stuff all over the rear tire and wheel.
I think that the small diameter of the tires leaves little free space compared to the rim size? I doubt that wife and I will wear these Shinkos out in our lifetimes (about 500 miles a year at most
Recently installed new Shinko 3.5-10 tires. I do my own tire installs, for my Burgman 400.
WOW. This was a PAIN (for Buddy). Hard to get old ones off, used tons of WD-40 which usually works for me.
Really hard to install new ones. Couldn't get the tires to pop. Even using medium sized air compressor, which is my last resort usually.
Had to take to a tire shop. They must have had a tough time too, there was soapy stuff all over the rear tire and wheel.
I think that the small diameter of the tires leaves little free space compared to the rim size? I doubt that wife and I will wear these Shinkos out in our lifetimes (about 500 miles a year at most
-
- Member
- Posts: 1157
- Joined: Sun Mar 30, 2008 9:17 pm
- Location: Norfolk VA
Re: DIY tire install comments
Last time we (friend and I) did Buddy 10" tires they kicked our butts! But we get 'em on without dinging the rim lip up. Now the last Buddy tire I took to a local shop. Get the wheel back and there's a big old ding/dent on the lip. It wasn't my Buddy and I had to pay for it so I really didn't care. In the end it did teach me to never use that dealer for any further services. I have a local Honda dealership that does the install for $20, off the bike, if you buy the tire from them. Never a mark or scratch on any wheel and their tire prices are very fair. Plus the tires are full warrantied and not blems or dead stock. That's who I use exclusively now. But 10" and smaller, like a super dreaded 8", are beast to do.
- eggsalad
- Member
- Posts: 236
- Joined: Sat Mar 14, 2020 8:42 pm
- Location: Las Vegas
Re: DIY tire install comments
I was gonna try it with the Kenda K329 I bought recently. That tire sells for $31 on Amazon.
I found a local shop, Motorcycle Tire Center Las Vegas (https://www.mtclv.com/) where the out-the-door price was $49, including mounting and a new valve stem ($5?).
So I basically paid $13 to get the tire mounted. For me at least, $13 is a bargain, compared to fighting to mount it myself.
I found a local shop, Motorcycle Tire Center Las Vegas (https://www.mtclv.com/) where the out-the-door price was $49, including mounting and a new valve stem ($5?).
So I basically paid $13 to get the tire mounted. For me at least, $13 is a bargain, compared to fighting to mount it myself.
- DeeDee
- Member
- Posts: 1110
- Joined: Sat Jul 26, 2014 5:07 pm
- Location: Denver
Re: DIY tire install comments
Heat is your friend. Set the wheel in direct sun for a half hour or so. Once you have broken the bead on both sides, it also helps to keep the tire sides pinched together in the center of the wheel. Use Irwin clamps if you have to. This will give you more tire to stretch over the wheel. I mount all my own tires. I do snow tires for my car as well. I just mounted a car tire on the rear of my Burgman. I became sick of paying $100 for a tire that wore out in less than two oil changes. The car tire cost $35 shipped to my door. It should last 25,000 miles give or take.
- Attachments
-
- Screenshot 2021-06-01 2.45.21 PM.png (107.39 KiB) Viewed 2611 times
Less chit chat, more riding, Buddy 50, 125, 170i, RH50, Yamaha C3
- tenders
- Member
- Posts: 419
- Joined: Mon Dec 03, 2018 1:08 am
- Location: NYC area
Re: DIY tire install comments
I too find tire changes too much of a PITA to DIY...and I consider DIY to be part of the fun of scooter ownership.
Little tires don't have the same flex and give as big tires to muscle the beads around the edges of the rims - ATV tires are the same way.
So I'm delighted to pay a shop whatever they want to put new tires on the rims, in the hope that they'll be around when I *really* need them.
Little tires don't have the same flex and give as big tires to muscle the beads around the edges of the rims - ATV tires are the same way.
So I'm delighted to pay a shop whatever they want to put new tires on the rims, in the hope that they'll be around when I *really* need them.
- Jasar13
- Member
- Posts: 2
- Joined: Mon Oct 29, 2018 1:04 am
- Location: Seminole FL
Re: DIY tire install comments
This may be a basic question but when do I need to change tires? I understand riding conditions vary. I have a Buddy 50 with 4700 miles on it. How long should they last?
- DeeDee
- Member
- Posts: 1110
- Joined: Sat Jul 26, 2014 5:07 pm
- Location: Denver
Re: DIY tire install comments
If there are no visible cracks, and they hold pressure ride them just pass the wear indicator. I see tire replacements around 6,000 miles on the rear and over double that on the front. I'm cheap. My ideal indicator is 10 miles before it blows.
- Attachments
-
- Screenshot 2021-06-02 7.41.17 AM.png (144.45 KiB) Viewed 2597 times
Less chit chat, more riding, Buddy 50, 125, 170i, RH50, Yamaha C3
- babblefish
- Member
- Posts: 3118
- Joined: Tue Dec 04, 2007 8:42 am
- Location: San Francisco
Re: DIY tire install comments
I've never had any problems seating a Michelin or Heidenau tire on my Buddy. I use a small 6 gallon compressor meant for pneumatic nail guns to inflate the tire. I seem to go through rear tires really fast though. Fronts are just a little longer lasting. And no, I'm not fat. Lol. I probably get 6-7K miles per rear tire.
Anyway, that being said, I don't really like changing my own tires, but I've always been too cheap to take it to a professional. My current rear Heidenau tire is almost down to it's inner fabric so it's time. I'm getting older now so I may just take the wheel to my dealer and have them change it this time.
Anyway, that being said, I don't really like changing my own tires, but I've always been too cheap to take it to a professional. My current rear Heidenau tire is almost down to it's inner fabric so it's time. I'm getting older now so I may just take the wheel to my dealer and have them change it this time.
Some people can break a crowbar in a sandbox.
-
- Member
- Posts: 721
- Joined: Thu Jul 12, 2012 3:40 am
- Location: Lake Geneva, WI
Re: DIY tire install comments
6-7k is good for a Buddy rear tire. I generally get 4-5k on the rear. The worst I've had was ~2,800, I think it wore out fast because it was 90+ degrees for most of those miles. The most miles was ~9k on the stock Cheng Shin C922.babblefish wrote: ↑Mon Jun 14, 2021 9:19 am I've never had any problems seating a Michelin or Heidenau tire on my Buddy. I use a small 6 gallon compressor meant for pneumatic nail guns to inflate the tire. I seem to go through rear tires really fast though. Fronts are just a little longer lasting. And no, I'm not fat. Lol. I probably get 6-7K miles per rear tire.
-
- Member
- Posts: 1157
- Joined: Sun Mar 30, 2008 9:17 pm
- Location: Norfolk VA
Re: DIY tire install comments
I was self installing a tire on a Zuma and put a long belt around the middle of the tire to help seat the bead easier. I went to inflate the tire and I forgot the compressor was set to 200psi! The belt snapped and slapped me on my chubby tummy! So don't forget to check the psi your using to seat the bead and don't lean over the tire, do everything from the side! Good news was the bead seated, so I didn't have to try it again.