Fishing rod holders
Moderator: Modern Buddy Staff
-
- Member
- Posts: 79
- Joined: Mon Feb 28, 2011 4:56 pm
- Location: NJ
Fishing rod holders
After an extensive search and some trial and error with certain brands of rod holders. I finally found something that fits on the rear rack, looks good and best of all, it work! It's from a company called All Rite Products. They make a rod holder and mount for ATVs. They can be found on various internet sites.
I'll post some pics soon. It's been raining for days.
I'll post some pics soon. It's been raining for days.
- klaborde
- Member
- Posts: 73
- Joined: Thu May 05, 2011 9:15 pm
- Location: Marietta, GA
-
- Member
- Posts: 79
- Joined: Mon Feb 28, 2011 4:56 pm
- Location: NJ
- neotrotsky
- Member
- Posts: 1546
- Joined: Wed Jun 01, 2011 8:48 am
- Location: Phoenix, AZ
- Contact:
WOO HOO! Finally a rack for my light sabers! Sweet
"Earth" without Art is just "Eh"...
<a href="http://slowkidsscootergang.wordpress.com/">The Slow Kids Scooter Gang</a>
<a href="http://slowkidsscootergang.wordpress.com/">The Slow Kids Scooter Gang</a>
- ScooterTrash
- Member
- Posts: 2007
- Joined: Sun Jun 03, 2007 5:00 pm
- Location: Idaho Falls, ID
- neotrotsky
- Member
- Posts: 1546
- Joined: Wed Jun 01, 2011 8:48 am
- Location: Phoenix, AZ
- Contact:
Shows what YOU know: Engine heat throws the alignment crystals out of wack. Duh.ScooterTrash wrote:Light Sabers fit under the seat rookieneotrotsky wrote:WOO HOO! Finally a rack for my light sabers! Sweet
"Earth" without Art is just "Eh"...
<a href="http://slowkidsscootergang.wordpress.com/">The Slow Kids Scooter Gang</a>
<a href="http://slowkidsscootergang.wordpress.com/">The Slow Kids Scooter Gang</a>
- BootScootin'FireFighter
- Member
- Posts: 2043
- Joined: Sun Jul 19, 2009 3:11 am
- Location: (Metro DC) Alexandria, Virginia
- Contact:
- Ray Knobs
- Member
- Posts: 683
- Joined: Wed Jun 18, 2008 3:55 pm
- Location: Rochester NY
- Contact:
- issue31
- Member
- Posts: 101
- Joined: Sun Apr 03, 2011 5:36 pm
- Location: Plainview MN.
FLY ROD HOLDER
PARTS:
5 or 6 feet 1 ½ in PVC pipe
1-End cap 1 ½
1- 1 ½ female pipe thread by clip coupling
1- 1 ½ PVC pipe plug
1- Small piece sponge to glue into end cap
2- 1 ½ electrical conduit clips
2- 3/8 x 1 bolts
2- 3/8 by 2 or 3 in carriage bolts
2- Larger finder washers
4- 3/8 wing nuts
pvc glue
Fit sponge into end cap, and glue to pvc pipe. This so rod does not hit end of cap.
Glue adapter to other end of pipe. Do not get glue on threads.
Put shorter bolts inside hole in clips.
Put clips on pipe with longer bolts and 2 wing nuts.
Put bolts through holes in milk crate. With fender washer and wing nuts.
Slide pipe up till you have enough room for your feet, tighten wing nuts.
Boots and Artic creel go in milk crate.
Fishing vest goes under seat.
GO FISHING!!!
Tryed to send pictures, still got something to LEARN! issue31
PARTS:
5 or 6 feet 1 ½ in PVC pipe
1-End cap 1 ½
1- 1 ½ female pipe thread by clip coupling
1- 1 ½ PVC pipe plug
1- Small piece sponge to glue into end cap
2- 1 ½ electrical conduit clips
2- 3/8 x 1 bolts
2- 3/8 by 2 or 3 in carriage bolts
2- Larger finder washers
4- 3/8 wing nuts
pvc glue
Fit sponge into end cap, and glue to pvc pipe. This so rod does not hit end of cap.
Glue adapter to other end of pipe. Do not get glue on threads.
Put shorter bolts inside hole in clips.
Put clips on pipe with longer bolts and 2 wing nuts.
Put bolts through holes in milk crate. With fender washer and wing nuts.
Slide pipe up till you have enough room for your feet, tighten wing nuts.
Boots and Artic creel go in milk crate.
Fishing vest goes under seat.
GO FISHING!!!
Tryed to send pictures, still got something to LEARN! issue31