Replacing Left Brake Lever
Moderator: Modern Buddy Staff
- sqrlbate
- Member
- Posts: 14
- Joined: Tue Jan 18, 2011 8:25 pm
- Location: Homewood, IL
Replacing Left Brake Lever
Long story short....Buddy 125 tipped over, left sided brake lever cracked. I got the replacement part but can't seem to find any step by step instructions on replacing it. Any advice???
- michelle_7728
- Member
- Posts: 1914
- Joined: Fri Jun 12, 2009 2:16 am
- Location: Renton, WA
The info from this thread was from a Buddy 150 St.Tropez, but I'd think it would be the same for a BlackJack...
viewtopic.php?t=5997&highlight=replace+brake+lever
viewtopic.php?t=5997&highlight=replace+brake+lever
Past bikes: 08' Genuine Buddy 125, '07 Yamaha Majesty 400, '07 Piaggio MP3 250, '08 Piaggio MP3 500, '08 Aprilia Scarabeo 500
Current bikes: Two '09 Genuine Buddy 125's
Current bikes: Two '09 Genuine Buddy 125's
-
- Member
- Posts: 68
- Joined: Thu Apr 21, 2011 2:17 am
- Location: Endicott
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
Were your scooters on the center stands when they tipped?
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
-
- Member
- Posts: 1450
- Joined: Mon Mar 30, 2009 4:18 pm
- Location: San Diego
cowl protectors. they don't just protect the cowls.
my scoot's been on its side 3 times - once I got hit and twice 60mph+ winds picked up and put it down (on its side). only the getting hit scratched the brake lever a wee bit but not once has it broken. It's cause (I think) the cowl protectors hit firsts and thus that handle bars don't take the beating
my scoot's been on its side 3 times - once I got hit and twice 60mph+ winds picked up and put it down (on its side). only the getting hit scratched the brake lever a wee bit but not once has it broken. It's cause (I think) the cowl protectors hit firsts and thus that handle bars don't take the beating
I had the same thing happen to me on a road trip in northwest Michigan. I kickstand-parked the scooter on a sloped surface, nudged it slightly, and over it went. SNAP. I tried the nearest scooter dealership that my phone could locate, about 5 miles away, and they had nothing that could fit: just parts for Vespas and motorhomes. So I scooted to Bayside Cycles of Frankfort MI, the nearest Genuine dealer: 40 miles with one brake thru the hills of northern Michigan (and in the opposite direction of my destination for that night).
The owner didn't have a brake lever in stock, but without me even asking he took one from one of his inventory bikes. He treated me like a valued customer, even though I was just passing through, and he was in the middle of some serious drama with his co-owner, who'd taken "his" tools home (requiring my guy to take a quick trip home to get his tools to do the job). Cost me $25, including labor. It also cost me a bit of time (I had to skip riding the beautiful Old Mission Peninsula to make up for it), but considering that this was the last Genuine dealer I'd be anywhere near for the next six days and several hundred miles, and even turning around and heading home would've been at least 150 miles of risky riding, I considered myself pretty damn lucky.
The owner didn't have a brake lever in stock, but without me even asking he took one from one of his inventory bikes. He treated me like a valued customer, even though I was just passing through, and he was in the middle of some serious drama with his co-owner, who'd taken "his" tools home (requiring my guy to take a quick trip home to get his tools to do the job). Cost me $25, including labor. It also cost me a bit of time (I had to skip riding the beautiful Old Mission Peninsula to make up for it), but considering that this was the last Genuine dealer I'd be anywhere near for the next six days and several hundred miles, and even turning around and heading home would've been at least 150 miles of risky riding, I considered myself pretty damn lucky.
- michelle_7728
- Member
- Posts: 1914
- Joined: Fri Jun 12, 2009 2:16 am
- Location: Renton, WA
Great customer service!!TVB wrote:I had the same thing happen to me on a road trip in northwest Michigan. I kickstand-parked the scooter on a sloped surface, nudged it slightly, and over it went. SNAP. I tried the nearest scooter dealership that my phone could locate, about 5 miles away, and they had nothing that could fit: just parts for Vespas and motorhomes. So I scooted to Bayside Cycles of Frankfort MI, the nearest Genuine dealer: 40 miles with one brake thru the hills of northern Michigan (and in the opposite direction of my destination for that night).
The owner didn't have a brake lever in stock, but without me even asking he took one from one of his inventory bikes. He treated me like a valued customer, even though I was just passing through, and he was in the middle of some serious drama with his co-owner, who'd taken "his" tools home (requiring my guy to take a quick trip home to get his tools to do the job). Cost me $25, including labor. It also cost me a bit of time (I had to skip riding the beautiful Old Mission Peninsula to make up for it), but considering that this was the last Genuine dealer I'd be anywhere near for the next six days and several hundred miles, and even turning around and heading home would've been at least 150 miles of risky riding, I considered myself pretty damn lucky.
Past bikes: 08' Genuine Buddy 125, '07 Yamaha Majesty 400, '07 Piaggio MP3 250, '08 Piaggio MP3 500, '08 Aprilia Scarabeo 500
Current bikes: Two '09 Genuine Buddy 125's
Current bikes: Two '09 Genuine Buddy 125's
- sqrlbate
- Member
- Posts: 14
- Joined: Tue Jan 18, 2011 8:25 pm
- Location: Homewood, IL
It's my mom's scoot that she had parked in my driveway long enough to close the garage door. I'm assuming it was on the side stand cuz she has a bit of a hard time getting the center stand down I was quite surprised how banged up it got just from tipping over, especially since she has the cowls on her Buddy. Guess it was just one of those freak things when gravity takes over & there's nothing you can do but stand there in horror & watch it hit the pavement. Glad to hear you had such great customer service! We live WAY too far from our shop here in Chicago so it was a DIY project I let a Harley friend of mine take care of. I tried to get him to ride it, no such luck
-
- Member
- Posts: 68
- Joined: Thu Apr 21, 2011 2:17 am
- Location: Endicott
- peabody99
- Member
- Posts: 1775
- Joined: Thu Jun 15, 2006 2:19 am
- Location: San Diego
I used the side stand ONCE on my first buddy. The remote opener to the garage was not working so Igot off to use the manual control and used the side instead of the center stand-like a dumb arse I left the engine running. The back wheel must have still been spinning becuase the engine was not warmed up and it caused it to topple. So I have never used the side stand again.
- goldscott
- Member
- Posts: 67
- Joined: Mon Apr 12, 2010 10:08 pm
- Location: San Diego, CA
I had my scooter on the center stand and it was so windy where I parked that it tipped over and broke the left brake lever as well.
It's pretty easy to just figure out how everything goes. Take the old one off and put the new one on in reverse order.
Basically just stick the end of the cable in and then put the bolt in and tighten it up.
It's pretty easy to just figure out how everything goes. Take the old one off and put the new one on in reverse order.
Basically just stick the end of the cable in and then put the bolt in and tighten it up.
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
The torque and vibration from the engine cycling is enough to take a scooter like the Buddy off its side stand.peabody99 wrote:I used the side stand ONCE on my first buddy. The remote opener to the garage was not working so Igot off to use the manual control and used the side instead of the center stand-like a dumb arse I left the engine running. The back wheel must have still been spinning becuase the engine was not warmed up and it caused it to topple. So I have never used the side stand again.
It's best to use the center stand at all times. A lot of people have trouble using it at first—even very small, featherweight people can do it once they learn how to. It just takes some practice!
At the very least, never use the side stand when the scooter is running.
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
- pdxrita
- Member
- Posts: 851
- Joined: Sat Jul 04, 2009 2:57 pm
- Location: Portland, OR
+1. I'm one of those small, featherweight people and I was able to centerstand a Buddy on the first try, which happened at a dealership because I was concerned that I wouldn't be able to do it. As a point of comparison, I tried to centerstand my partner's Kymco People 150 and couldn't do it to save my life (I've since learned how, as a result of learning on the Buddy). The Buddy is extremely easy to centerstand. I don't even think about it now, it's just automatic. I can't even remember the last time I used the side stand.ericalm wrote:It's best to use the center stand at all times. A lot of people have trouble using it at first—even very small, featherweight people can do it once they learn how to. It just takes some practice!
The key to it is understanding how to use your own weight (even if it's not a lot) for leverage. Don't try to pick up the scooter (at least not as the main source of power), but put your own weight down onto the lever of the stand, and let that do most of the work.ericalm wrote:It's best to use the center stand at all times. A lot of people have trouble using it at first—even very small, featherweight people can do it once they learn how to. It just takes some practice!
- pdxrita
- Member
- Posts: 851
- Joined: Sat Jul 04, 2009 2:57 pm
- Location: Portland, OR
I don't actually even use my weight; I had to centerstand it to see how I did it. I grab the handlebar with my left hand, rack with my right, and then just push back on the stand with my foot while guiding it back with both hands. It sounds hard, but it really doesn't require hardly any strength. It is possible for me to stand on the lever and use my ~100 lbs to push it down, but it's not necessary.TVB wrote:The key to it is understanding how to use your own weight (even if it's not a lot) for leverage. Don't try to pick up the scooter (at least not as the main source of power), but put your own weight down onto the lever of the stand, and let that do most of the work.ericalm wrote:It's best to use the center stand at all times. A lot of people have trouble using it at first—even very small, featherweight people can do it once they learn how to. It just takes some practice!
-
- Member
- Posts: 4
- Joined: Thu Nov 24, 2016 12:16 am
- Location: Pensacola, Florida
Left brake lever installation by lay person
Anyone break a left brake lever and install a new lever themselves? Please give me a link. or step by step procedure if you have an answer to this? Please and thank you!!! Buddy 50
-
- Member
- Posts: 367
- Joined: Wed Dec 30, 2015 5:43 am
- Location: College Station, TX
Re: Left brake lever installation by lay person
If you have the correct replacement lever, this is the procedure:paulremski777 wrote:Anyone break a left brake lever and install a new lever themselves? Please give me a link. or step by step procedure if you have an answer to this? Please and thank you!!! Buddy 50
1. Loosen up the rear brake cable by rotating the tensioning nut down put the rear wheel. Sometimes you can rotate it by hand or you may need a wrench (maybe 14mm?) if it is stuck.
2. Expose the base of the left brake handle by peeling up the black rubber cover that covers the pivot screw.
3. Remove the pivot screw with a screw driver on top and wrench (8mm?) underneath.
4. The handle should be able to be pulled out at this point. Pull it out as far as the slack in brake cable allows and rotate it around to expose the bottom of the brake lever.
5. Slide the handle off the little plug that holds the brake cable to the brake lever.
6. Install the replacement brake lever and reverse the steps above.
Steps 2-6 are easier if the top cover over the gauges is removed (a whole other process) but removing the top cover is not absolutely necessary, as I recall. You just have to work your screwdriver in between the plastic cover and the back of the left switch assembly.
Here is a video of the process: https://m.youtube.com/watch?v=CE_ARn9FD44
-
- Member
- Posts: 4
- Joined: Thu Nov 24, 2016 12:16 am
- Location: Pensacola, Florida
-
- Member
- Posts: 367
- Joined: Wed Dec 30, 2015 5:43 am
- Location: College Station, TX
- tiii
- Member
- Posts: 88
- Joined: Tue Jun 04, 2013 3:09 am
- Location: San Francisco
- Contact:
there should be enough grease from the first lever.
but, since you've got it appart anyway, use a dab of grease where the cable end slides into the lever.
but, since you've got it appart anyway, use a dab of grease where the cable end slides into the lever.
Tony
<img src=http://i100.photobucket.com/albums/m39/ ... ilwgp4.jpg>
<img src=http://i100.photobucket.com/albums/m39/ ... ilwgp4.jpg>