new here, long time looker, but now getting to posting. Since the pandemic, my Buddy 125 will be my primary way of getting downtown when I'm able to get back to my office. it needs some work. speedometer and odometer is not spinning (needs new cable most likely), new tires. oil change, gear oil, brakes.
i work on my car alot, so this does not intimidate me at all and I have the tools too. but when working on the front end, how would you support it? my car jack stands are not going to work. thank you all again. hope to hear from you soon.
supporting your buddy while working on it
Moderator: Modern Buddy Staff
-
- Member
- Posts: 5
- Joined: Mon May 04, 2020 12:56 pm
- Location: Denver
- jrsjr
- Moderator Emeritus
- Posts: 3746
- Joined: Fri Jun 09, 2006 11:26 pm
Honestly, I think I would just give this old thread a quick read before launching into a lot of involved work.
- JettaKnight
- Member
- Posts: 671
- Joined: Thu Mar 29, 2007 2:19 am
- Location: Fort Wayne
- DeeDee
- Member
- Posts: 1107
- Joined: Sat Jul 26, 2014 5:07 pm
- Location: Denver
If you plan on pulling your front wheel, you probably want to support the scooter. I use an 1100 lb mini lift, but I work on a lot of scooters. Before I bought the lift, I would use a square milk crate or empty 3 gallon bucket to hold the front of the scooter up.
- Attachments
-
- Screenshot 2020-05-05 at 7.30.29 PM.png (191.13 KiB) Viewed 1398 times
-
- Screenshot 2020-05-05 at 7.35.10 PM.png (180.53 KiB) Viewed 1398 times
-
- Member
- Posts: 5
- Joined: Mon May 04, 2020 12:56 pm
- Location: Denver
- tenders
- Member
- Posts: 419
- Joined: Mon Dec 03, 2018 1:08 am
- Location: NYC area
I bought an inexpensive motorcycle scissor lift soon after acquiring my first scooter. I discovered that it does not work particularly well with scooters' underbelly shape or weight distribution, and is not worth the garage space.
https://www.harborfreight.com/1500-lb-c ... 60536.html
(anybody in the NY area want it?)
https://www.harborfreight.com/1500-lb-c ... 60536.html
(anybody in the NY area want it?)
- babblefish
- Member
- Posts: 3118
- Joined: Tue Dec 04, 2007 8:42 am
- Location: San Francisco
FWIW, I've taken the front wheel off of my Buddy to change the tire while the Buddy was on it's center stand with no issues. The rear end of the scooter is naturally heavier than the front so the front stays in the air but to be sure I put a little weight on the rear rack.
And as far as your speedometer not working, the first thing I would check is to make sure the speedometer cable that goes from the front wheel to the speedometer is still connected correctly on the bottom of the speedometer. People have had this cable fall off or someone has installed it wrong where the center cable was not fully engaged in the hole of the speedometer. It's a square hole to match the square stub at the end of the speedo cable.
And as far as your speedometer not working, the first thing I would check is to make sure the speedometer cable that goes from the front wheel to the speedometer is still connected correctly on the bottom of the speedometer. People have had this cable fall off or someone has installed it wrong where the center cable was not fully engaged in the hole of the speedometer. It's a square hole to match the square stub at the end of the speedo cable.
Some people can break a crowbar in a sandbox.
- Point37
- Member
- Posts: 402
- Joined: Thu Mar 08, 2018 4:34 pm
- Location: Southcoast, MA
had 1 of these for my yamaha tw200 but it only has a 300lb capacity...the nice thing was i could jack the bike up high...had to ride up a thick board to get the clearance to slide it under
https://www.gregsmithequipment.com/Motocross-Lift-Red
https://www.gregsmithequipment.com/Motocross-Lift-Red
'10 Triumph Bonneville SE (sold), '00 Yamaha TW200 (sold), '08 Husqvarna SM510R (sold), '05 Honda CBR 600RR (sold), '03 Honda CBR 600RR (sold)