DR 177 kit issue.
Moderator: Modern Buddy Staff
-
- Member
- Posts: 23
- Joined: Sat Apr 18, 2020 1:32 pm
DR 177 kit issue.
just finished insalling my DR 177 piston and before I put on the cylinder, I pushed down on the kick started slowly to make sure I get smooth piston action and it stops at the bottm of the stroke. Like its hitting something. I have it in neutral and cannot figure out why the engine doesnt spin freely. Any ideas??
- Mr.FixIt
- Member
- Posts: 152
- Joined: Wed Aug 01, 2018 1:44 pm
- Location: York, PA, USA
- Contact:
Its easy enough to pull the gudgeon pin back out and look inside the crank chamber. There should be no foreign objects for certain and the crank should turn smoothly with you guiding the connecting rod from banging against the side.
Second make certain that the rings are not getting hung up on the ports in the cylinder. Push the piston down in the cylinder without having it on the connecting rod. It should be smooth.
I don't know why it doesn't come this way, but did you chamfer the ports in the cylinder wall?
https://www.scooterwest.com/port-chamfe ... amfer.html
Second make certain that the rings are not getting hung up on the ports in the cylinder. Push the piston down in the cylinder without having it on the connecting rod. It should be smooth.
I don't know why it doesn't come this way, but did you chamfer the ports in the cylinder wall?
https://www.scooterwest.com/port-chamfe ... amfer.html
Eric
(aka Mr. Fix It)
(aka Mr. Fix It)
-
- Member
- Posts: 23
- Joined: Sat Apr 18, 2020 1:32 pm
- Mr.FixIt
- Member
- Posts: 152
- Joined: Wed Aug 01, 2018 1:44 pm
- Location: York, PA, USA
- Contact:
Was the decision to upgrade to the DR177 just an upgrade, or due to some failure with the original cylinder?
I would agree, the crank should spin freely when the gear selector is in neutral.
Pull the fan cover and make sure nothing has fallen down in there. Check the bendix on the electric starter to make sure it isn't catching on the flywheel teeth. Of course you've looked in the crank chamber itself with a flashlight. There should be no foreign parts in there.
Beyond that, any obstruction would have to be inside the gearbox section of the engine.
I would agree, the crank should spin freely when the gear selector is in neutral.
Pull the fan cover and make sure nothing has fallen down in there. Check the bendix on the electric starter to make sure it isn't catching on the flywheel teeth. Of course you've looked in the crank chamber itself with a flashlight. There should be no foreign parts in there.
Beyond that, any obstruction would have to be inside the gearbox section of the engine.
Eric
(aka Mr. Fix It)
(aka Mr. Fix It)
- BuddyRaton
- Scooter Dork
- Posts: 3887
- Joined: Sat Sep 09, 2006 10:08 pm
- Location: Boca Raton, Florida
- Contact:
It could be anything. Had to open a friends back up and found a woodruff key in there. Don't force anything.
Agree with chamfering ports when you are at that point.
I would pull the clutch out and see what happens. At least you will know if it's in the motor or gearbox.
Unless you get lucky and it's something that can be flushed from the trans open it back up.
Agree with chamfering ports when you are at that point.
I would pull the clutch out and see what happens. At least you will know if it's in the motor or gearbox.
Unless you get lucky and it's something that can be flushed from the trans open it back up.
"Things fall apart - it's scientific" - David Byrne
www.teamscootertrash.com
'06 Cream Buddy 125, 11 Blur 220, 13 BMW C 650 GT, 68 Vespa SS180, 64 Vespa GS MK II, 65 Lambretta TV 175, 67 Vespa GT, 64 Vespa 150 VBB 64 Vespa GL
www.teamscootertrash.com
'06 Cream Buddy 125, 11 Blur 220, 13 BMW C 650 GT, 68 Vespa SS180, 64 Vespa GS MK II, 65 Lambretta TV 175, 67 Vespa GT, 64 Vespa 150 VBB 64 Vespa GL
-
- Member
- Posts: 23
- Joined: Sat Apr 18, 2020 1:32 pm
Went back to look further and the crank stops at t the bottom of the intake stroke and towards the top of the compression stroke. I know nothing dropped inside cant figure this out. I may have to drain the gear oil just to see if that helps. Starter bendix is free. Sounds like its hitting a solid wall.
-
- Member
- Posts: 23
- Joined: Sat Apr 18, 2020 1:32 pm
well I finally found the obstruction. I got lucky when after blowing inside the intake under the reed valve , a small washer that nbarely could fit through the oil drain hole c, came out into my drain pan. I thanked God that I didnt have to take apart the engine bottom. Got real lucky. Everything is back to normal. Now back to the 180 kit install. Thnx to all your responses.
- Mr.FixIt
- Member
- Posts: 152
- Joined: Wed Aug 01, 2018 1:44 pm
- Location: York, PA, USA
- Contact: