SIMPLE MOD QUESTION
Moderator: Modern Buddy Staff
-
- Member
- Posts: 50
- Joined: Sun Feb 07, 2010 3:47 pm
- Location: Cortlandt Manor, NY
SIMPLE MOD QUESTION
I am thinking of doing some simple mods I've seen on Voodoo site, but don't want to keep changing things ever time I make a mod.
1st mod will be drilling airbox out. What size jets should I get?
2nd mod cvt stage 2 upgrade. Will I have to change the jets or can I keep the smae ones from the airbox mod?
3rd mod prima exhaust. If and when I do this upgrade do I have to change jets again?
Thanks for the help
1st mod will be drilling airbox out. What size jets should I get?
2nd mod cvt stage 2 upgrade. Will I have to change the jets or can I keep the smae ones from the airbox mod?
3rd mod prima exhaust. If and when I do this upgrade do I have to change jets again?
Thanks for the help
- Kaos
- Member
- Posts: 4892
- Joined: Mon May 19, 2008 5:39 pm
- Location: Portland, OR
Re: SIMPLE MOD QUESTION
I'll try to answer these in order you posted them.jcbud wrote:I am thinking of doing some simple mods I've seen on Voodoo site, but don't want to keep changing things ever time I make a mod.
1st mod will be drilling airbox out. What size jets should I get?
2nd mod cvt stage 2 upgrade. Will I have to change the jets or can I keep the smae ones from the airbox mod?
3rd mod prima exhaust. If and when I do this upgrade do I have to change jets again?
Thanks for the help
1) Jet size will depend on your altitude and location, and is one of the hardest mods to say "just install this one" I went from a #95 to a #105 at first, then a #110 later, so figure you'll be going up several sizes. Best bet is to buy a kit that contains between a #100 and #120.
2) The changes to the CVT won't require re-jetting. You're good here.
3) You don't HAVE to change jets with the pipe, but you'll likely want to. The pipe will lean out your mixture, and a bigger jet will likely help. That being said, if you're a bit rich when you jet up for the airbox mod, you'll likely be just right when you install the pipe.
Good luck!
-
- Member
- Posts: 2037
- Joined: Mon Jul 24, 2006 9:57 pm
- Location: Next to a big dirt lot.
- Contact:
I modded the airbox (drilled out 3 holes and removed the "wall" that the rubber hose inserts into) and installed the Prima pipe. Had to jet up from the stock 85 to 115. I live at 3200 ft. elevation.
--Keys
P.S. Of course there are some on this forum who think I'm an idiot and don't know what I'm talking about, so take it for what it's worth.
--Keys
P.S. Of course there are some on this forum who think I'm an idiot and don't know what I'm talking about, so take it for what it's worth.
"Life without music would Bb"
- Lostmycage
- FAQ Moderator
- Posts: 4062
- Joined: Tue Jun 17, 2008 3:36 am
- Location: The Interwebz!
Yeah, don't you start forgetting stuff if you've been at something longer than most people?Keys wrote:I modded the airbox (drilled out 3 holes and removed the "wall" that the rubber hose inserts into) and installed the Prima pipe. Had to jet up from the stock 85 to 115. I live at 3200 ft. elevation.
--Keys
P.S. Of course there are some on this forum who think I'm an idiot and don't know what I'm talking about, so take it for what it's worth.
Check out Scoot Richmond's new site: My awesome local shop.
- Lostmycage
- FAQ Moderator
- Posts: 4062
- Joined: Tue Jun 17, 2008 3:36 am
- Location: The Interwebz!
Most shops will charge a minimum of an hour.
Changing jets is a lazy 15 minutes or "work". The first time will take a considerable amount of time longer, of course.
Now if it's re-jetting and dialing in, that's a lot more time. Expect about 3 hours of labor which will include test rides.
Personally, I wouldn't recommend any performance mods unless you do them yourself or more importantly you know how to undo them if if they brake.
Changing jets is a lazy 15 minutes or "work". The first time will take a considerable amount of time longer, of course.
Now if it's re-jetting and dialing in, that's a lot more time. Expect about 3 hours of labor which will include test rides.
Personally, I wouldn't recommend any performance mods unless you do them yourself or more importantly you know how to undo them if if they brake.
Check out Scoot Richmond's new site: My awesome local shop.
- Cheshire
- Member
- Posts: 1976
- Joined: Sat Jun 28, 2008 5:27 pm
- Location: near Asheville, NC
Good idea to know how to go back a step if the mod breaks. You want to undo that mod VERY quickly if it starts braking...unless it was the front disc rotor.Lostmycage wrote:Personally, I wouldn't recommend any performance mods unless you do them yourself or more importantly you know how to undo them if if they brake.
- ScooterTrash
- Member
- Posts: 2007
- Joined: Sun Jun 03, 2007 5:00 pm
- Location: Idaho Falls, ID
Tuning is VERY difficult to do correctly. Nobody can tell you what jet to run, even if they live next door and have the same mods yours will be a bit different. If you don't know how to read plugs you shouldn't even bother (unless you pay to have it tuned).Lostmycage wrote:Most shops will charge a minimum of an hour.
Changing jets is a lazy 15 minutes or "work". The first time will take a considerable amount of time longer, of course.
Now if it's re-jetting and dialing in, that's a lot more time. Expect about 3 hours of labor which will include test rides.
Personally, I wouldn't recommend any performance mods unless you do them yourself or more importantly you know how to undo them if if they brake.
One tip I have is try to always fill up at the same gas station. this will keep your burn rate more consistent (water content is different at all stations)
Even reading plugs on these is hard because you can't cut the fuel when you shut the bike off thanks to vacuum. So you will be loading the cylinder with unburned fuel if you don't stop fast enough
VooDoo is a very accurate term
- Kaos
- Member
- Posts: 4892
- Joined: Mon May 19, 2008 5:39 pm
- Location: Portland, OR
Absolutely. With the CVK carbs, a plug cut is hard to do, unless you're crazy enough to try running it on a stand at WOT then stop it hard.ScooterTrash wrote:Tuning is VERY difficult to do correctly. Nobody can tell you what jet to run, even if they live next door and have the same mods yours will be a bit different. If you don't know how to read plugs you shouldn't even bother (unless you pay to have it tuned).Lostmycage wrote:Most shops will charge a minimum of an hour.
Changing jets is a lazy 15 minutes or "work". The first time will take a considerable amount of time longer, of course.
Now if it's re-jetting and dialing in, that's a lot more time. Expect about 3 hours of labor which will include test rides.
Personally, I wouldn't recommend any performance mods unless you do them yourself or more importantly you know how to undo them if if they brake.
One tip I have is try to always fill up at the same gas station. this will keep your burn rate more consistent (water content is different at all stations)
Even reading plugs on these is hard because you can't cut the fuel when you shut the bike off thanks to vacuum. So you will be loading the cylinder with unburned fuel if you don't stop fast enough
VooDoo is a very accurate term
Learning to read a plug is a must if you want to do this without always paying your mechanic to tune it for ya
- ScooterTrash
- Member
- Posts: 2007
- Joined: Sun Jun 03, 2007 5:00 pm
- Location: Idaho Falls, ID
I just use widebandKaos wrote:Absolutely. With the CVK carbs, a plug cut is hard to do, unless you're crazy enough to try running it on a stand at WOT then stop it hard.ScooterTrash wrote:Tuning is VERY difficult to do correctly. Nobody can tell you what jet to run, even if they live next door and have the same mods yours will be a bit different. If you don't know how to read plugs you shouldn't even bother (unless you pay to have it tuned).Lostmycage wrote:Most shops will charge a minimum of an hour.
Changing jets is a lazy 15 minutes or "work". The first time will take a considerable amount of time longer, of course.
Now if it's re-jetting and dialing in, that's a lot more time. Expect about 3 hours of labor which will include test rides.
Personally, I wouldn't recommend any performance mods unless you do them yourself or more importantly you know how to undo them if if they brake.
One tip I have is try to always fill up at the same gas station. this will keep your burn rate more consistent (water content is different at all stations)
Even reading plugs on these is hard because you can't cut the fuel when you shut the bike off thanks to vacuum. So you will be loading the cylinder with unburned fuel if you don't stop fast enough
VooDoo is a very accurate term
Learning to read a plug is a must if you want to do this without always paying your mechanic to tune it for ya
- Kaos
- Member
- Posts: 4892
- Joined: Mon May 19, 2008 5:39 pm
- Location: Portland, OR
I'll clarify, on *A* stand. If you're gonna try this DON'T use the center stand. It folds up. If it does that when you're at WOT, bad things will happen! I strap mine down to a motorcycle jack with U-bolts.ScooterTrash wrote:I just use widebandKaos wrote:Absolutely. With the CVK carbs, a plug cut is hard to do, unless you're crazy enough to try running it on a stand at WOT then stop it hard.ScooterTrash wrote: Tuning is VERY difficult to do correctly. Nobody can tell you what jet to run, even if they live next door and have the same mods yours will be a bit different. If you don't know how to read plugs you shouldn't even bother (unless you pay to have it tuned).
One tip I have is try to always fill up at the same gas station. this will keep your burn rate more consistent (water content is different at all stations)
Even reading plugs on these is hard because you can't cut the fuel when you shut the bike off thanks to vacuum. So you will be loading the cylinder with unburned fuel if you don't stop fast enough
VooDoo is a very accurate term
Learning to read a plug is a must if you want to do this without always paying your mechanic to tune it for ya
- ScooterTrash
- Member
- Posts: 2007
- Joined: Sun Jun 03, 2007 5:00 pm
- Location: Idaho Falls, ID
Mine doesn't fold upKaos wrote:I'll clarify, on *A* stand. If you're gonna try this DON'T use the center stand. It folds up. If it does that when you're at WOT, bad things will happen! I strap mine down to a motorcycle jack with U-bolts.ScooterTrash wrote:I just use widebandKaos wrote: Absolutely. With the CVK carbs, a plug cut is hard to do, unless you're crazy enough to try running it on a stand at WOT then stop it hard.
Learning to read a plug is a must if you want to do this without always paying your mechanic to tune it for ya
- Kaos
- Member
- Posts: 4892
- Joined: Mon May 19, 2008 5:39 pm
- Location: Portland, OR
Yeah yeah, fansy locking centerstand mod.... Show offScooterTrash wrote:Mine doesn't fold upKaos wrote:I'll clarify, on *A* stand. If you're gonna try this DON'T use the center stand. It folds up. If it does that when you're at WOT, bad things will happen! I strap mine down to a motorcycle jack with U-bolts.ScooterTrash wrote: I just use wideband
- Cheshire
- Member
- Posts: 1976
- Joined: Sat Jun 28, 2008 5:27 pm
- Location: near Asheville, NC
Just don't accidentally lean on the back of the scooter when you're testing....ScooterTrash wrote:Mine doesn't fold upKaos wrote:I'll clarify, on *A* stand. If you're gonna try this DON'T use the center stand. It folds up. If it does that when you're at WOT, bad things will happen! I strap mine down to a motorcycle jack with U-bolts.ScooterTrash wrote: I just use wideband
- ScooterTrash
- Member
- Posts: 2007
- Joined: Sun Jun 03, 2007 5:00 pm
- Location: Idaho Falls, ID
- ScooterTrash
- Member
- Posts: 2007
- Joined: Sun Jun 03, 2007 5:00 pm
- Location: Idaho Falls, ID
- pyrocpu
- Member
- Posts: 193
- Joined: Tue Jun 16, 2009 12:24 am
- Location: Nashville, TN
Well... I wonder... I suppose you COULD lock up the rear (somehow anyway, since the RR drum plain sucks), hit the kill switch, and remember not to let off the RR brake until you come to a complete stop, and pull your plug on the side of the road?
Granted, what one could do isn't necessarily the same as one should/shouldn't do...
Granted, what one could do isn't necessarily the same as one should/shouldn't do...
- Kaos
- Member
- Posts: 4892
- Joined: Mon May 19, 2008 5:39 pm
- Location: Portland, OR
Yeah, that COULD be done. Probably shouldn't though I'm not sure you could lock up the rear though, as its not the greatest brake. Just stopping hard works well enough though.pyrocpu wrote:Well... I wonder... I suppose you COULD lock up the rear (somehow anyway, since the RR drum plain sucks), hit the kill switch, and remember not to let off the RR brake until you come to a complete stop, and pull your plug on the side of the road?
Granted, what one could do isn't necessarily the same as one should/shouldn't do...
- Lostmycage
- FAQ Moderator
- Posts: 4062
- Joined: Tue Jun 17, 2008 3:36 am
- Location: The Interwebz!
Sounds like you're trying to figure out how to post in two threads at once. This one and the crash thread.pyrocpu wrote:Well... I wonder... I suppose you COULD lock up the rear (somehow anyway, since the RR drum plain sucks), hit the kill switch, and remember not to let off the RR brake until you come to a complete stop, and pull your plug on the side of the road?
Granted, what one could do isn't necessarily the same as one should/shouldn't do...
Q: What were you doing?
A: Plug chop
Q: Was there any damage to the bike?
A: It's totaled, but that sucker's tuned!
Check out Scoot Richmond's new site: My awesome local shop.
-
- Member
- Posts: 50
- Joined: Sun Feb 07, 2010 3:47 pm
- Location: Cortlandt Manor, NY
http://www.battlescooter.com/1.html
great great rejetting info
did my mods and had no problem.
the exhaust is a straight bolt off and on. also did the DIY airbox mod.
with those 2 done I hit the jets. You must have the correct screwdriver size 1st and 2nd patience.
I started with 100 jet, it ran terrible. took that out and installed 95 jet, ran better but still not great. I then left the 95 on and started to reverse some of the airbox mods. 1st reinstalled the snorkel.....ran better but still alittle off. then added back the seperation piece in the airbox......ran perfect.
a few thing that might help if someone does re-jetting..keep a golf tee handy, you can use it to stop the gas line with it.
great great rejetting info
did my mods and had no problem.
the exhaust is a straight bolt off and on. also did the DIY airbox mod.
with those 2 done I hit the jets. You must have the correct screwdriver size 1st and 2nd patience.
I started with 100 jet, it ran terrible. took that out and installed 95 jet, ran better but still not great. I then left the 95 on and started to reverse some of the airbox mods. 1st reinstalled the snorkel.....ran better but still alittle off. then added back the seperation piece in the airbox......ran perfect.
a few thing that might help if someone does re-jetting..keep a golf tee handy, you can use it to stop the gas line with it.