do you need any special tools to install compression spring?

Discussion of the Genuine Buddy, Hooligan, Black Jack and other topics, both scooter related and not

Moderator: Modern Buddy Staff

Post Reply
User avatar
jasondavis48108
Member
Posts: 2919
Joined: Fri Apr 24, 2009 12:36 pm
Location: Ann Arbor

do you need any special tools to install compression spring?

Post by jasondavis48108 »

o.k., so I've ordered the stage 1 kit for my Buddy 50 and it comes with the yellow 1500rpm compression spring for the clutch. I have been reading how-tos and watching videos and some folks say you don't need any special tools, some folks say you do, and some folks beat on it with a hammer and screw driver :lol: Just wondering what folks here have used when they changed that spring. btw I do have tons of regular tools so thats not a problem and I just bought an impact wrench and sockets today. Just wondering if you need one of those clutch compressing tools or any other scooter specific tools.

also, I know the prima rollers don't last long but is there any other reason not to play with them for awhile? If not I figured I'd install them and when they wore out I'd replace them with the dr pulley weights.

Thanx
"Only the curious have, if they live, a tale worth telling at all" Alastair Reid
User avatar
bigbropgo
Member
Posts: 1607
Joined: Thu Jul 31, 2008 1:41 am
Location: gotham city and the 801

Post by bigbropgo »

I didn't have a special tool. I did have two C-clamps to compress everything together. I forgot I had them and thought to set it on the garage floor and stand on the sides....pretty ghetto I know.
no i don't ride a scooter, i am a scooter pilot!
Image
VICTUS MORTUUS VENATOR
Image
User avatar
jasondavis48108
Member
Posts: 2919
Joined: Fri Apr 24, 2009 12:36 pm
Location: Ann Arbor

Post by jasondavis48108 »

excellent, I have a whole bunch of C-clamps :)
"Only the curious have, if they live, a tale worth telling at all" Alastair Reid
User avatar
JettaKnight
Member
Posts: 671
Joined: Thu Mar 29, 2007 2:19 am
Location: Fort Wayne

Post by JettaKnight »

I just did this tonight. Pretty easy the second time.

Set the pulley on the ground and plate the spring and clutch on top. Sit on a chair in front of the pulley. Place both of your feet on the clutch and press down. You'll need to line up the notches, this might take a couple of attempts. When you press in on, use your hands to screw on the nut.

Be careful, the 1500 spring has a lot of potential energy.
User avatar
toycoma98
Member
Posts: 150
Joined: Sat Mar 06, 2010 7:46 am
Location: Guam

Post by toycoma98 »

just step on it and screw the nut! nevermind the clamps.
Image
User avatar
Lostmycage
FAQ Moderator
Posts: 4062
Joined: Tue Jun 17, 2008 3:36 am
Location: The Interwebz!

Post by Lostmycage »

I wouldn't use the C-clamps. There's too big a chance of them slipping once under compression. You'll poke your eye out... actually, you'll poke your face off.
Check out :arrow: Scoot Richmond's new site: My awesome local shop.
User avatar
jasondavis48108
Member
Posts: 2919
Joined: Fri Apr 24, 2009 12:36 pm
Location: Ann Arbor

Post by jasondavis48108 »

Lostmycage wrote:you'll poke your face off.
:shock:

:rofl:

yeah, definitely don't want to do that. I found a video on 49ccscooter.com that shows how to disassemble with a vice and reassemble by stepping on it. Looks fairly easy although I'm sure its only that easy the 100th time around.
"Only the curious have, if they live, a tale worth telling at all" Alastair Reid
User avatar
NASRA
Member
Posts: 72
Joined: Fri Jun 25, 2010 7:31 pm
Location: Indy
Contact:

Post by NASRA »

If you do this often a company called ZTR racing products makes a nice tool to help get the job done. I have one in my shop and I love it.
Amerivespa Indy 2015.
Scooterists start your engines!

#AVINDY15
User avatar
db
Member
Posts: 187
Joined: Sun May 27, 2007 2:31 pm
Location: Denver, CO

Post by db »

That tool looks like it could have helped me big time a while ago, thanks for sharing
User avatar
PIStaker
Member
Posts: 334
Joined: Wed Jul 02, 2008 2:57 am
Location: Chicago, IL

my $ .02

Post by PIStaker »

Getting it off the first time is definitely a challenge. I used the strap wrench method that I saw online. I would say it's not as easy as everyone makes it out to be, if you're going ghetto like I did. (the strap wrench broke in the process)
But, like any shop project, if you have the right tools, it should make for a less stressful experience.
Do your research.
Once you loosen the screw, the rest is pretty easy.
User avatar
jasondavis48108
Member
Posts: 2919
Joined: Fri Apr 24, 2009 12:36 pm
Location: Ann Arbor

Post by jasondavis48108 »

I did take the clutch apart yesterday and replaced the spring. Your right, its not as easy as they make it look in the videos. That big thin nut is really on there tight. I had to use a strap wrench since my metal oil filter wrench was not large enough to fit around the clutch. It really tok an effort on my part but I finally got it off. I think it will probably be easier next time around. Thanks for everybodies input. It really makes it a lot easier to start playing around with the machine when you have a good community like this to help ya out :D
"Only the curious have, if they live, a tale worth telling at all" Alastair Reid
User avatar
NASRA
Member
Posts: 72
Joined: Fri Jun 25, 2010 7:31 pm
Location: Indy
Contact:

Post by NASRA »

A good investment is a 36mm socket and a electric impact gun if you plan on tinkering with your CVT. Makes life so much easier. 8)
Amerivespa Indy 2015.
Scooterists start your engines!

#AVINDY15
User avatar
jasondavis48108
Member
Posts: 2919
Joined: Fri Apr 24, 2009 12:36 pm
Location: Ann Arbor

Post by jasondavis48108 »

NASRA wrote:A good investment is a 36mm socket and a electric impact gun if you plan on tinkering with your CVT. Makes life so much easier. 8)
I was wondering what size the bolt was. nothing I had would fit so i had to use my vice and the strap wrench, what a pain in the arse :lol:

btw how do folks put the nut back on the variator and the clutch bell? Getting it off with the impact wrench was easy, but I had to try and hold it still with a strap wrench in one hand while I used the torque wrench with the other to get it back on, yet another pain in the arse.
"Only the curious have, if they live, a tale worth telling at all" Alastair Reid
User avatar
NASRA
Member
Posts: 72
Joined: Fri Jun 25, 2010 7:31 pm
Location: Indy
Contact:

Post by NASRA »

Just hold the rear wheel and use the impact to install the nut.
Amerivespa Indy 2015.
Scooterists start your engines!

#AVINDY15
User avatar
jasondavis48108
Member
Posts: 2919
Joined: Fri Apr 24, 2009 12:36 pm
Location: Ann Arbor

Post by jasondavis48108 »

NASRA wrote:Just hold the rear wheel and use the impact to install the nut.
wow, you can do that? Do you have some special tool that regulates torque on the imapct wrench or does the torque value just not matter that much on the variator and clutch bell nuts?
"Only the curious have, if they live, a tale worth telling at all" Alastair Reid
User avatar
NASRA
Member
Posts: 72
Joined: Fri Jun 25, 2010 7:31 pm
Location: Indy
Contact:

Post by NASRA »

jasondavis48108 wrote:
NASRA wrote:Just hold the rear wheel and use the impact to install the nut.
wow, you can do that? Do you have some special tool that regulates torque on the imapct wrench or does the torque value just not matter that much on the variator and clutch bell nuts?
I do it mostly on feel. I have my impact set to hammer at around 45ftpnds and I use a little blue locktight on each bolt I install including these. Never had a problem.

However you must be careful not to over torque the bolts as you can strip the treads out on the crankshaft and rear axle. Seen it done before and there is no easy fix for that issue.
Amerivespa Indy 2015.
Scooterists start your engines!

#AVINDY15
User avatar
jasondavis48108
Member
Posts: 2919
Joined: Fri Apr 24, 2009 12:36 pm
Location: Ann Arbor

Post by jasondavis48108 »

NASRA wrote:
jasondavis48108 wrote:
NASRA wrote:Just hold the rear wheel and use the impact to install the nut.
wow, you can do that? Do you have some special tool that regulates torque on the imapct wrench or does the torque value just not matter that much on the variator and clutch bell nuts?
I do it mostly on feel. I have my impact set to hammer at around 45ftpnds and I use a little blue locktight on each bolt I install including these. Never had a problem.

However you must be careful not to over torque the bolts as you can strip the treads out on the crankshaft and rear axle. Seen it done before and there is no easy fix for that issue.
Yikes! my impact gun cant be set for a particular torque guess I'll stick to the pain in the arse method for now. :lol:
"Only the curious have, if they live, a tale worth telling at all" Alastair Reid
Post Reply