Engine power loss during commute this morning
Moderator: Modern Buddy Staff
- ed85379
- Member
- Posts: 510
- Joined: Thu Apr 15, 2010 10:00 pm
- Location: Boston
Engine power loss during commute this morning
My brand new Blackjack. Has 180 miles on it as of this morning.
Three times on the way into work this morning, first the exhaust started popping, and then I would suddenly lose engine power while driving. After pulling over, the engine would stall completely, and then gave me trouble starting it back up.
It wasn't vapor lock, because I popped the gas cap off after the first time. No burst of pressure, and it continued to happen two more times. But the next two times were in relative quick succession, and then I managed to drive another 20 minutes with no more trouble.
This never happened to my old Blackjack, and this is the first trouble I've had with the new one.
Any ideas? A bit of bad gas had to be worked out perhaps? Think I should bring it into the shop today? Seems a shame to bring it there when I am so close to the first maintenance.
Three times on the way into work this morning, first the exhaust started popping, and then I would suddenly lose engine power while driving. After pulling over, the engine would stall completely, and then gave me trouble starting it back up.
It wasn't vapor lock, because I popped the gas cap off after the first time. No burst of pressure, and it continued to happen two more times. But the next two times were in relative quick succession, and then I managed to drive another 20 minutes with no more trouble.
This never happened to my old Blackjack, and this is the first trouble I've had with the new one.
Any ideas? A bit of bad gas had to be worked out perhaps? Think I should bring it into the shop today? Seems a shame to bring it there when I am so close to the first maintenance.
-
- Member
- Posts: 379
- Joined: Sun May 01, 2011 5:01 am
- Location: BHC AZ
- Contact:
Its not common but tolerances at the factory can be set too tight and as the engine brakes in going through a substantial amount of "metal ware brake in", those tolerances can become too close causing the valves to escape gas and and begin to burn. Follow the service manual and check your valve clearance, look at your spark plug burn color, make sure there are no obstructions like a plastic bag blocking airflow cooling, check your air intake box for rat litter, check your oil level, do a compression test and check your jets for an obstruction.
If I have even the slightest hint that one of my bike is having trouble, I stop riding and find the problem.
If I have even the slightest hint that one of my bike is having trouble, I stop riding and find the problem.
- ed85379
- Member
- Posts: 510
- Joined: Thu Apr 15, 2010 10:00 pm
- Location: Boston
So in other words, bring it to the shop. Since I have no idea how to actually check any of those things. A mechanic, I am not.CWO4GUNNER wrote:Its not common but tolerances at the factory can be set too tight and as the engine brakes in going through a substantial amount of "metal ware brake in", those tolerances can become too close causing the valves to escape gas and and begin to burn. Follow the service manual and check your valve clearance, look at your spark plug burn color, make sure there are no obstructions like a plastic bag blocking airflow cooling, check your air intake box for rat litter, check your oil level, do a compression test and check your jets for an obstruction.
If I have even the slightest hint that one of my bike is having trouble, I stop riding and find the problem.
Unfortunately, half-way to work was not a reasonable time to "stop riding", and I still have to get it home too. Though the shop is only about 1 mile from work.
-
- Member
- Posts: 1329
- Joined: Sat Nov 07, 2009 12:22 am
- Location: Maryland
Mechanic will have to check for all of the stuff you mentioned but one thing strikes me in what you said: plastic bag blocking air flow. Where or how would something like this occur?CWO4GUNNER wrote:Its not common but tolerances at the factory can be set too tight and as the engine brakes in going through a substantial amount of "metal ware brake in", those tolerances can become too close causing the valves to escape gas and and begin to burn. Follow the service manual and check your valve clearance, look at your spark plug burn color, make sure there are no obstructions like a plastic bag blocking airflow cooling, check your air intake box for rat litter, check your oil level, do a compression test and check your jets for an obstruction.
If I have even the slightest hint that one of my bike is having trouble, I stop riding and find the problem.
Today I packed my underseat compartment pretty tightly. More so then usual. Could soemthing there cause problem?
I am not a scooter snob.
I am a scooter connoisseur
I am a scooter connoisseur
- PeteH
- Member
- Posts: 2281
- Joined: Mon Jan 17, 2011 4:32 pm
- Location: 3603mi SE of Dutch Harbor
Nah - the Bud doesn't draw cooling air from the pet carrier. Instead, there is a black plastic air intake on the right-hand side of the engine that actually opens downward. This scoop gathers the air that circulates around the outside of the cylinder head (not combustion air). There are anecdotal stories of paper or plastic bags getting sucked up off the road ane into this cooling intake, blocking airflow and semi-overheating the engine.
Just reach up into the scoop and feel for any baggage.
Just reach up into the scoop and feel for any baggage.
-
- Member
- Posts: 1329
- Joined: Sat Nov 07, 2009 12:22 am
- Location: Maryland
Just came back from fishing expedition - nothing. I e-mailed my mechanic. Hopefully we can get in to see him soon. Poor Dobby was just fine this weekend. I rode to work, then dentist - no problems whatsoever. I I vary speed, just like I am supposed to during break-in period. Dobby is still under warranty. If our mechanic decides to honor it, that is......PeteH wrote:Nah - the Bud doesn't draw cooling air from the pet carrier. Instead, there is a black plastic air intake on the right-hand side of the engine that actually opens downward. This scoop gathers the air that circulates around the outside of the cylinder head (not combustion air). There are anecdotal stories of paper or plastic bags getting sucked up off the road and into this cooling intake, blocking airflow and semi-overheating the engine.
Just reach up into the scoop and feel for any baggage.
I am not a scooter snob.
I am a scooter connoisseur
I am a scooter connoisseur
- jmkjr72
- Member
- Posts: 783
- Joined: Sat Jul 11, 2009 11:07 pm
- Location: green bay wi
- Contact:
- pdxrita
- Member
- Posts: 851
- Joined: Sat Jul 04, 2009 2:57 pm
- Location: Portland, OR
It does sound like a trip to the mechanic is in order, especially since your scoot is so new. But I wouldn't write off the possibility of vapor lock so quickly. When I experienced vapor lock, I also dismissed that as a possibility because I didn't hear any suction when I removed my gas cap. But that's what it turned out to be. In my case, my gas had been overfilled by a helpful gas station attendant. When I got down to about 1/4 tank, I started experiencing backfires and loss of power followed by stalling. I drilled little holes in my gas cap and have not had any issues since.
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
Re: Engine power loss during commute this morning
It may still have been vapor (or vacuum) lock. You won't always hear a burst of pressure. Did you leave the gas cap off after removing it or replace it?ed85379 wrote:It wasn't vapor lock, because I popped the gas cap off after the first time. No burst of pressure, and it continued to happen two more times. But the next two times were in relative quick succession, and then I managed to drive another 20 minutes with no more trouble.
I was riding with a friend on a BlackJack who experienced this. It was def. vapor (vacuum) lock. I removed the gas cap (no "whoosh"), started it up and ran the engine for a minute, revving it. Replaced gas cap and off we went. Then it happened again a couple minutes later. The solution was to just leave the gas cap off for a while. Her tank was not full, it wasn't hot outside. It can just happen like this.
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
- ed85379
- Member
- Posts: 510
- Joined: Thu Apr 15, 2010 10:00 pm
- Location: Boston
I did put the cap back on. Would hate for the gas to splash into the underseat carrier.
The scooter was fine for the ride home. So, I filled the tank and added an oz of Seafoam. I expect it'll be fine.
The scooter was fine for the ride home. So, I filled the tank and added an oz of Seafoam. I expect it'll be fine.
Last edited by ed85379 on Tue May 10, 2011 3:52 am, edited 1 time in total.
- pdxrita
- Member
- Posts: 851
- Joined: Sat Jul 04, 2009 2:57 pm
- Location: Portland, OR
So you were almost empty? That's exactly what happened to me. I'd fill it up and it would be fine until I got low again. I'm voting vapor lock.ed85379 wrote:I did put the cap back on. Would take for the gas to splash into the underseat carrier.
The scooter was fine for the ride home. So, I filled the tank and added an oz of Seafoam. I expect it'll be fine.
- ed85379
- Member
- Posts: 510
- Joined: Thu Apr 15, 2010 10:00 pm
- Location: Boston
I was at a quarter tank.pdxrita wrote:So you were almost empty? That's exactly what happened to me. I'd fill it up and it would be fine until I got low again. I'm voting vapor lock.ed85379 wrote:I did put the cap back on. Would take for the gas to splash into the underseat carrier.
The scooter was fine for the ride home. So, I filled the tank and added an oz of Seafoam. I expect it'll be fine.
-
- Member
- Posts: 379
- Joined: Sun May 01, 2011 5:01 am
- Location: BHC AZ
- Contact:
You don't have to necessarily be a "mechanic" to do the things I mentioned becasue they are considered the basic that can be learned by anyone. When I was 16 I couldn't afford a new car or mechanic and attended a basic community college course at night twice a week, auto repair 101 and auto body 101. Shop class was fun and taught me the basics and from there whenever I needed to learn some new procedure I just cracked a shop manual, did some research and took my time. I always had 2 used cars to trade off whenever one needed repairs. Since then 38 years to the present the only thing I take my vehicles to the mechanic for are tire changes and wheel balancing, so I got a big return on my investment.
- ed85379
- Member
- Posts: 510
- Joined: Thu Apr 15, 2010 10:00 pm
- Location: Boston
I realize one doesn't need to be a mechanic. However, what I meant by that, is that I am not a gear-head at all, have very little interest in the inner-workings of motor vehicles, so have never taken the time or had enough interest to bother learning. The electronics I can deal with, but the engine and valves and such, I haven't a clue.CWO4GUNNER wrote:You don't have to necessarily be a "mechanic" to do the things I mentioned becasue they are considered the basic that can be learned by anyone. When I was 16 I couldn't afford a new car or mechanic and attended a basic community college course at night twice a week, auto repair 101 and auto body 101. Shop class was fun and taught me the basics and from there whenever I needed to lean something new I just cracked a shop manual, did some research and took my time. I always had 2 used cars to trade off whenever one needed repairs. Since then 38 years to the present the only thing I take my vehicles to the mechanic for are tire changes and wheel balancing, so I got a big return on my investment.
-
- Member
- Posts: 1329
- Joined: Sat Nov 07, 2009 12:22 am
- Location: Maryland
Now the newbie question ; where are the valves and how to I get to the jets (whatever they are and wherever they are?)CWO4GUNNER wrote: Follow the service manual and check your valve clearance, look at your spark plug burn color, make sure there are no obstructions like a plastic bag blocking airflow cooling, check your air intake box for rat litter, check your oil level, do a compression test and check your jets for an obstruction.
I am not a scooter snob.
I am a scooter connoisseur
I am a scooter connoisseur
-
- Member
- Posts: 379
- Joined: Sun May 01, 2011 5:01 am
- Location: BHC AZ
- Contact:
Stormswift wrote:Now the newbie question ; where are the valves and how to I get to the jets (whatever they are and wherever they are?)CWO4GUNNER wrote: Follow the service manual and check your valve clearance, look at your spark plug burn color, make sure there are no obstructions like a plastic bag blocking airflow cooling, check your air intake box for rat litter, check your oil level, do a compression test and check your jets for an obstruction.
Well besides the basic know how (hand tools and concepts) that's necessary from an experienced instructor or well experienced friend, the answer is on page 30 of the owners manual and page 28 of the shop manual. No matter how much you learn and experience wrenching, a successful mechanic will always have the service manual procedure reviewed and the book cracked for reference during the procedure. That is how its done, everything else is just hearsay.
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
Valve adjustments:Stormswift wrote:Now the newbie question ; where are the valves and how to I get to the jets (whatever they are and wherever they are?)CWO4GUNNER wrote: Follow the service manual and check your valve clearance, look at your spark plug burn color, make sure there are no obstructions like a plastic bag blocking airflow cooling, check your air intake box for rat litter, check your oil level, do a compression test and check your jets for an obstruction.
topic8312.html
topic5671.html
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
- jrsjr
- Moderator Emeritus
- Posts: 3746
- Joined: Fri Jun 09, 2006 11:26 pm
If you've never set the valves on a motor before, get somebody to walk you through it. It's possible to damage your motor by making a mistake setting the valves. Don't ask me how I know this.ericalm wrote:Valve adjustments:Stormswift wrote:Now the newbie question ; where are the valves and how to I get to the jets (whatever they are and wherever they are?)CWO4GUNNER wrote: Follow the service manual and check your valve clearance, look at your spark plug burn color, make sure there are no obstructions like a plastic bag blocking airflow cooling, check your air intake box for rat litter, check your oil level, do a compression test and check your jets for an obstruction.
topic8312.html
topic5671.html
-
- Member
- Posts: 1329
- Joined: Sat Nov 07, 2009 12:22 am
- Location: Maryland
<------------- (in a faint on the ground next to Dobby). Not in this recarnation. Perhaps next time I will come back as a master mechanic. Dobby will just have to get over his belly ache with the use of a scooter laxative (aka Seafoam).
Strange thing is instead of getting vapor lock after longer ride it actually performs like its old self - speed goes back to normal, etc. I am totally buffled
Strange thing is instead of getting vapor lock after longer ride it actually performs like its old self - speed goes back to normal, etc. I am totally buffled
I am not a scooter snob.
I am a scooter connoisseur
I am a scooter connoisseur
- Skootz Kabootz
- Member
- Posts: 4305
- Joined: Sat Nov 15, 2008 12:47 pm
- Location: West Hollywood, CA
- Contact:
My scooter LOVES going for long hard rides. The harder and faster I ride it the happier it gets. It get's more responsive, runs smoother, and just all around feels peppier. Just like how happy a dog gets when it finally gets to go outside for a good run after being cooped up inside for too long. It just comes alive. I think the hard riding must simply clear things out in the engine. In my experience a scooter that only get ridden at 1/4 throttle for short distances is the equivalent to a scooter couch potato. Scooters need a good workout to be at their best.Stormswift wrote:Strange thing is instead of getting vapor lock after longer ride it actually performs like its old self - speed goes back to normal, etc. I am totally buffled
-
- Member
- Posts: 1329
- Joined: Sat Nov 07, 2009 12:22 am
- Location: Maryland
It is gremlins, I tell you. That is the real answer. Get yourselves Guardian bells and holly water or whatever you believe in . THEY ARE OUT THERE
Scoots, you are right about my scooter: it has bee a couch potato for almost 2 years thanks to it's owner taking her time getting licensed. I started real riding just last month. Before it was weekends
Scoots, you are right about my scooter: it has bee a couch potato for almost 2 years thanks to it's owner taking her time getting licensed. I started real riding just last month. Before it was weekends
I am not a scooter snob.
I am a scooter connoisseur
I am a scooter connoisseur
-
- Member
- Posts: 379
- Joined: Sun May 01, 2011 5:01 am
- Location: BHC AZ
- Contact:
Early in my military career at age 19 (1976) I would work part time for an Iranian named Johnny who had a VW Bug (air cooled) repair shop. He taught me more in one summer then night class class ever did from adjusting valves to assembling entire engines for customers strait from the machine shop. after a while he let me re-build my own Bug I picked up at the junk yard for $300. In a few months I had the fasted VW on base oversize from 1200CC to 1700CC, man could that car fly, understand that a 1966 VW bug only weighed about 1700, half the weight of today's Honda accord.
He taught me to check the valve clearance twice after adjustment each time rotating the engine by hand in the direction of rotation and stopping at TDC. He always told me "Always do good honest work, but never work cheap"LOL
He taught me to check the valve clearance twice after adjustment each time rotating the engine by hand in the direction of rotation and stopping at TDC. He always told me "Always do good honest work, but never work cheap"LOL
-
- Member
- Posts: 28
- Joined: Sat May 07, 2011 2:37 am
- Location: mchenry il
having the same problem with my blackjack...only 141 mi on her too...throttle went out after my first over 10 mi run on her...she is still in the shop they have had her for 14 days now...and they still cant figure it out...they said its something electrical..now mind you this is a brand new scooter..so i had the bike in my posession for 5 days the shop has now had it for 14..and they still arent sure whats wrong with it..i have not had a great experience with my blackjack...hopefully this gets taken care of in the next week so i can actually enjoy my scooter
- Raiderfn31
- Member
- Posts: 655
- Joined: Sat Mar 19, 2011 9:37 pm
- Location: Charlotte, N.C.
I could not agree more. I have 250 miles on my St Tropez and have JUST begun to go full throttle for short burst. Its like the machine is asking for more. Plus its so cool to look in the rear view and see dots where cars used to be.Skootz Kabootz wrote:My scooter LOVES going for long hard rides. The harder and faster I ride it the happier it gets. It get's more responsive, runs smoother, and just all around feels peppier. Just like how happy a dog gets when it finally gets to go outside for a good run after being cooped up inside for too long. It just comes alive. I think the hard riding must simply clear things out in the engine. In my experience a scooter that only get ridden at 1/4 throttle for short distances is the equivalent to a scooter couch potato. Scooters need a good workout to be at their best.Stormswift wrote:Strange thing is instead of getting vapor lock after longer ride it actually performs like its old self - speed goes back to normal, etc. I am totally buffled
"When your lawyer looks at you like you deserve whats coming, you may begin to sweat."
- Skootz Kabootz
- Member
- Posts: 4305
- Joined: Sat Nov 15, 2008 12:47 pm
- Location: West Hollywood, CA
- Contact:
I first noticed the performance improvement in particular after we did a 1200 mile ride from LA to Los Gatos and back, much of it WOT. My scooter was already broken in at that point but it was like it broke in again differently. The scooter just seemed to settle in to the higher RPM's and faster speed like it was its favorite comfy chair or something. Now, if I don't take it for a good run pretty frequently, it starts to get a little pissy with meRaiderfn31 wrote:I could not agree more. I have 250 miles on my St Tropez and have JUST begun to go full throttle for short burst. Its like the machine is asking for more. Plus its so cool to look in the rear view and see dots where cars used to be.Skootz Kabootz wrote:My scooter LOVES going for long hard rides. The harder and faster I ride it the happier it gets. It get's more responsive, runs smoother, and just all around feels peppier. Just like how happy a dog gets when it finally gets to go outside for a good run after being cooped up inside for too long. It just comes alive. I think the hard riding must simply clear things out in the engine. In my experience a scooter that only get ridden at 1/4 throttle for short distances is the equivalent to a scooter couch potato. Scooters need a good workout to be at their best.Stormswift wrote:Strange thing is instead of getting vapor lock after longer ride it actually performs like its old self - speed goes back to normal, etc. I am totally buffled
- zilla86
- Member
- Posts: 83
- Joined: Tue May 10, 2011 7:03 am
- Location: So Cal W.L.A.
Man I almost feel guilty not having a single problem with my new Blackjack.
I have over 500 miles on my scooter in 3 weeks of ownership and I think those of you that have done the long hard rides are on to something.
I do the same every chance I get and my Blackjack just seems to run smoother and faster after each ride.
I know we all have new 2009 Blackjack's but who know's how long our dealers had our scoots before we picked them up.
and more important what type of periodic maintenance was done while these scoots set at the dealer if any at all.
I went over my Buddy with a fine tooth comb after getting it home
and I could see my dealer did a great job setting it up. It has run like I expected with no issues at all.I checked all screws,nuts,wires,conectors etc. and they were all tight and in good shape.
It's been a while since I've owned a carbureted bike/scooter and in a way I'm glad to have it again
I hope you get your Blackjack sorted so you can enjoy this great little scooter.
I have over 500 miles on my scooter in 3 weeks of ownership and I think those of you that have done the long hard rides are on to something.
I do the same every chance I get and my Blackjack just seems to run smoother and faster after each ride.
I know we all have new 2009 Blackjack's but who know's how long our dealers had our scoots before we picked them up.
and more important what type of periodic maintenance was done while these scoots set at the dealer if any at all.
I went over my Buddy with a fine tooth comb after getting it home
and I could see my dealer did a great job setting it up. It has run like I expected with no issues at all.I checked all screws,nuts,wires,conectors etc. and they were all tight and in good shape.
It's been a while since I've owned a carbureted bike/scooter and in a way I'm glad to have it again
I hope you get your Blackjack sorted so you can enjoy this great little scooter.
- michelle_7728
- Member
- Posts: 1914
- Joined: Fri Jun 12, 2009 2:16 am
- Location: Renton, WA
- ed85379
- Member
- Posts: 510
- Joined: Thu Apr 15, 2010 10:00 pm
- Location: Boston
-
- Member
- Posts: 379
- Joined: Sun May 01, 2011 5:01 am
- Location: BHC AZ
- Contact:
I think Im going to install a gas filter. You don't see them anymore but they used to be common place, clear plastic and visible so you could see what your fuel looked like. Would catch dirt, water and you cold see it but would keep it from collecting in your carb bowl.
IN GOD I TRUST http://cwo4gunnerguscgretired.blogspot.com/
- CEZ2011
- Member
- Posts: 32
- Joined: Fri Jun 03, 2011 3:23 am
- Location: Alexandria, VA
I am just curious. What problem are you experiencing with your Buddy?jmkjr72 wrote:well i would have the valves checkd and also check the ele conections around the coil
i ahve heard that there is a chance that a wire can work looose and might cause an issue like that too
The problem you are experiencing may be some entirely unrelated to valve train and or carburetor issues. It could be something simple.
Valve adjustments and carb jetting are not difficult for someone who has experience working with engines but may not be the best job to attempt if you are a novice mechanic. Basic maintenance such as oil and filter changes are good place to start.
- Raiderfn31
- Member
- Posts: 655
- Joined: Sat Mar 19, 2011 9:37 pm
- Location: Charlotte, N.C.
I need to bite the bullet and do the same thing.CWO4GUNNER wrote:You don't have to necessarily be a "mechanic" to do the things I mentioned becasue they are considered the basic that can be learned by anyone. When I was 16 I couldn't afford a new car or mechanic and attended a basic community college course at night twice a week, auto repair 101 and auto body 101. Shop class was fun and taught me the basics and from there whenever I needed to learn some new procedure I just cracked a shop manual, did some research and took my time. I always had 2 used cars to trade off whenever one needed repairs. Since then 38 years to the present the only thing I take my vehicles to the mechanic for are tire changes and wheel balancing, so I got a big return on my investment.
"When your lawyer looks at you like you deserve whats coming, you may begin to sweat."
- Dean F
- Member
- Posts: 247
- Joined: Sat Jul 19, 2008 8:31 pm
- Location: Chicago/Hinsdale
You have one now but it is not clear, it is opaque. The stock one is about $17 and comes with new fuel lines. I change mine when I change my belt, plug, etc. (a full tune up).CWO4GUNNER wrote: think Im going to install a gas filter. You don't see them anymore but they used to be common place, clear plastic and visible so you could see what your fuel looked like. Would catch dirt, water and you cold see it but would keep it from collecting in your carb bowl.
Member 2715
Chrome Rear Rack
Genuine Top Case
Black Grips
Chrome Front Rack
Garmin GPS & Ram Mount
PIAA HS1
13g Dr. Pully Sliders
Everstart 9-BS AGM Battery
Chrome Rear Rack
Genuine Top Case
Black Grips
Chrome Front Rack
Garmin GPS & Ram Mount
PIAA HS1
13g Dr. Pully Sliders
Everstart 9-BS AGM Battery
- Raiderfn31
- Member
- Posts: 655
- Joined: Sat Mar 19, 2011 9:37 pm
- Location: Charlotte, N.C.
nice to see that link you have isnt attachedCWO4GUNNER wrote:You don't have to necessarily be a "mechanic" to do the things I mentioned becasue they are considered the basic that can be learned by anyone. When I was 16 I couldn't afford a new car or mechanic and attended a basic community college course at night twice a week, auto repair 101 and auto body 101. Shop class was fun and taught me the basics and from there whenever I needed to learn some new procedure I just cracked a shop manual, did some research and took my time. I always had 2 used cars to trade off whenever one needed repairs. Since then 38 years to the present the only thing I take my vehicles to the mechanic for are tire changes and wheel balancing, so I got a big return on my investment.
"When your lawyer looks at you like you deserve whats coming, you may begin to sweat."