New 4T exhaust from Tasso
Moderator: Modern Buddy Staff
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
New 4T exhaust from Tasso
Well, even ordering from the UK, this came out to be less than the other performance exhausts I could find for the 4T, $237 shipped.
That seems like a lot but it's about the same as the Gianelli pipe (without shipping) and much less than the Pinasco at $430 (before shipping).
So, what the heck. I'll give this a try. I need a better pipe.
http://www.lmlparts.co.uk/cgi-bin/store ... =&uid=1046
That seems like a lot but it's about the same as the Gianelli pipe (without shipping) and much less than the Pinasco at $430 (before shipping).
So, what the heck. I'll give this a try. I need a better pipe.
http://www.lmlparts.co.uk/cgi-bin/store ... =&uid=1046
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
- listless
- Member
- Posts: 86
- Joined: Wed Mar 23, 2011 8:38 pm
- Location: Lee, MA UNITED STATES
- Contact:
- jimmbomb
- Member
- Posts: 801
- Joined: Fri May 20, 2011 1:00 am
- Location: St Louis
listless wrote:Loud? Why does everyone want loud?
I just want a little more power and a pipe that doesn't break apart
Lots of people like loud pipes.
I do because I want people to hear me coming.
Car and bike shows bring out the loud pipes. It's a show.
They expect a show. Lots of folks are counting on people with loud pipes.
I try not to disappoint.
Good luck
J H
[URL=https:///][/URL] upload pics
[URL=https:///][/URL] upload pics
-
- Member
- Posts: 214
- Joined: Fri Aug 17, 2012 12:25 pm
There is a video of it running here,the pipe also comes with a DB killer which makes it a little more 'neighbour friendly'.
http://youtu.be/xUKQpdcl6tU
http://youtu.be/xUKQpdcl6tU
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
Install tomorrow! It's a pretty direct bolt-on. Looks like it can be oriented for right or left sides. I haven't ordered jets; I'll have to see if the local guys have any or wait to rejet.
The pipe appears very solid and well-made.
The pipe appears very solid and well-made.
- Attachments
-
- tasso_4t-small.jpg (101.53 KiB) Viewed 4150 times
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
- Neurotic-Hapi-Snak
- Member
- Posts: 335
- Joined: Thu Jun 05, 2014 2:56 am
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
"Void your warranty" is pretty relative. Basically, if something not related to the exhaust goes bad or if you have a problem that can't be traced to the exhaust you should be covered.
I have a few more pics that I'll post. The install is easy as can be. The mounting is pretty basic, a U-bolt and bracket. I may fashion something more attractive and functional later.
The sound is nice. Quiet at idle, nice, satisfying rumble under throttle.
<iframe width="560" height="315" src="//www.youtube.com/embed/aoz7fSD4wfM?rel=0" frameborder="0" allowfullscreen></iframe>
I have a few more pics that I'll post. The install is easy as can be. The mounting is pretty basic, a U-bolt and bracket. I may fashion something more attractive and functional later.
The sound is nice. Quiet at idle, nice, satisfying rumble under throttle.
<iframe width="560" height="315" src="//www.youtube.com/embed/aoz7fSD4wfM?rel=0" frameborder="0" allowfullscreen></iframe>
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
- Neurotic-Hapi-Snak
- Member
- Posts: 335
- Joined: Thu Jun 05, 2014 2:56 am
- jimmbomb
- Member
- Posts: 801
- Joined: Fri May 20, 2011 1:00 am
- Location: St Louis
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
I'll be upjetting to a 92 or 95. Plug looks pretty good, though, all things considered. A tad lean.
It doesn't have the rhythm of a 2t and it's not as loud as many. It's a deeper, richer sound than stock and is louder when revved. Just not TOO loud.
It doesn't have the rhythm of a 2t and it's not as loud as many. It's a deeper, richer sound than stock and is louder when revved. Just not TOO loud.
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
-
- Member
- Posts: 162
- Joined: Thu Apr 18, 2013 5:19 am
- Location: Vista CA (San Diego)
- Contact:
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
It's pretty straightforward. Yup, you can keep the spare.
The holes in the included bracket were too small for the bolt that goes through the swingarm, so I had to widen one of them. It's secure, for now, but I still want to fashion something better together. Shouldn't be too hard, even for me.
Performance wise, hard to tell. Maybe a tiny improvement. But I haven't rejetted or done anything to the air filter yet. I have a Ram Air I may add after the rejetting. Ordered #92 and #95 main jets and two larger idle jets.
But it's running at least as good as stock now. The air/fuel was already dialed a bit richer than stock setup.
The holes in the included bracket were too small for the bolt that goes through the swingarm, so I had to widen one of them. It's secure, for now, but I still want to fashion something better together. Shouldn't be too hard, even for me.
Performance wise, hard to tell. Maybe a tiny improvement. But I haven't rejetted or done anything to the air filter yet. I have a Ram Air I may add after the rejetting. Ordered #92 and #95 main jets and two larger idle jets.
But it's running at least as good as stock now. The air/fuel was already dialed a bit richer than stock setup.
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
- Neurotic-Hapi-Snak
- Member
- Posts: 335
- Joined: Thu Jun 05, 2014 2:56 am
I wouldn't ride it too much until you rejet. The factory jetting is a tad lean, probably not too bad in hot Cali, with a pipe you're probably way too lean. I'd guess you'll probably have to use the 95 main jet. On my Stella it was a touch lean with the stock 90 main so I went up to a 92, runs better now, everything stock. Idle will probably go up one step. Just be prepared for a lot of trial and error and taking apart the carb. If you haven't already, grab a handful of replacement plugs to take clean readings off of.
Also, I said it sounds sort of like a 2T (in the video), with a higher, raspier note than a usual 4T exhaust. You definitely wouldn't be mistaking it for a 2T at all. As Eric said, it's actually deeper than the stock exhaust, so the audio on the video is off.
Also, I said it sounds sort of like a 2T (in the video), with a higher, raspier note than a usual 4T exhaust. You definitely wouldn't be mistaking it for a 2T at all. As Eric said, it's actually deeper than the stock exhaust, so the audio on the video is off.
-
- Member
- Posts: 162
- Joined: Thu Apr 18, 2013 5:19 am
- Location: Vista CA (San Diego)
- Contact:
Re: Agreed
This video will essentially show you how to do that (carb jet cleaning portion):srbbnd wrote:toot wrote:Post pics of install and jet change... Make it a HOW TO!!! That way I can do it myself when I need a New Exhaust
http://vimeo.com/20618680
-
- Member
- Posts: 214
- Joined: Fri Aug 17, 2012 12:25 pm
They have got new hangers made up and are sending them out for people to retrofit.
Here is a quick review I wrote for the LML owners club -
It's early days for this exhaust and I know that Tasso are listening to customer feedback and improving the design as they go a long so if you buy one and think that it could be improved in some way let them know.
-Build quality.
The exhaust feels solid,the metal is thick without being too heavy (it weighs less than the standard exhaust) and it feel like it could survive a few winters (only time will tell).
The machined manifolds are a thing of beauty.
-Fit.
This is probably what lets the exhaust down the most. The pipe comes with a strip of metal with holes in it which you have to bend to shape around your exhaust to create a kind of hanger. You then use the shorter bolt supplied to bolt the 'hanger' to itself around the exhaust and the longer of the bolts is used to bolt the hanger to the swing arm.
Bending the plate is a bit of a pain in the arse and it took me a fair few attempts until I got it into the right shape. The fitting instructions could do with a diagram. I also scratched the paint of the exhaust a fair bit in the process of bending the plate (Tasso are aware of this issue).
The longer bolt to attach the hanger to the swing arm is a smaller diameter than the hole in the swing arm. Some people would be happy with this but back in the day I used a thinner bolt to attach an exhaust to my old 2t and it ended up wearing it's way through the swing arm.
I decided to drill out the hole in the hanger and use a standard size swing arm bolt and nut that I had spare.
In the end I gave up on all the bending and Tasso sent me a pre-bent strip of metal which made life much easier.
I know they are looking into alternative ways of supporting the exhaust at the swing arm.
The tricky part with fitting the exhaust is there are a lot of variables. The position on the hanger on the pipe,the angle the tail pipe point (up/down),how far the curved tail pipe is pushed on to the down pipe,which side of the swing arm the hanger sits,the angle of the down pipe from manifold. Tou also have to insure the tail pipe clears both rear and spare tyre (which it does if angles correctly).
This means the pipe doesn't just bolt on it more a case of bolt on,adjust,adjust,adjust.
Tasso have designed the pipe this way so that users can configure it how they want it but in my opinion people would much rather have a one piece pipe with welded bracket that was quick,simple and easy to fit. They have taken this on board.
My test ride was cut short because when I pulled over to check everything was ok I noticed the tail pipe had dropped a fair amount and was pointing down towards the road. I pulled it back up again and road home (over about 4 speed bumps) and when I got home the pipe had dropped again.
The tail pipe on the 200 model is a fair bit longer than the 125/150 model which means there is a fair bit of unsupported weight/twisting force at the tail end of the pipe. I am not sure if the U bolt is enough to stop this 'droopage'. I reported this back to Tasso and hopefully the new 'hanger' will solve this issue.
-Sound.
Tasso have been experimenting a lot to get the sound right and all the experimenting has paid off.
The pipe sounds meaty without being stupidly loud. You could happily ride down a residential street late at night without pissing the neighbours off too much but when you open the throttle it growls !
Performance-
There was no obvious performance boost from the exhaust although it seem to vibrate a lot less than a standard exhaust. I will be booking the scoot in at a dyno to get some science based numbers at some point in the future.
My scooter has a ram air filter fitted with a 95 main jet which to me felt spot on.
Summary-
It's a solid feeling,cheap to buy alternative to the other exhaust for the 4t on the market. The general 'brief' Tasso were working to was to create an exhaust that won't fall apart every six months,that sounds good and performs better than standard.
I think they have managed this and the price is fantastic but I do think there are a few little design problems that need ironing out.
If you have never fitted a scooter exhaust before then get someone who has to help you because this one is a little tricky.
For now I have re-fitted my standard exhaust. My scooter is my soul method of transport and I use it every day so I can't risk having something work loose while I am heading to do my weekly shop.
Luckily Tasso are being very proactive and improving the design based on customer feedback so it won't be long before they get it perfect.
(This review is based on my personal experience,other peoples experiences may differ)
Here is a quick review I wrote for the LML owners club -
It's early days for this exhaust and I know that Tasso are listening to customer feedback and improving the design as they go a long so if you buy one and think that it could be improved in some way let them know.
-Build quality.
The exhaust feels solid,the metal is thick without being too heavy (it weighs less than the standard exhaust) and it feel like it could survive a few winters (only time will tell).
The machined manifolds are a thing of beauty.
-Fit.
This is probably what lets the exhaust down the most. The pipe comes with a strip of metal with holes in it which you have to bend to shape around your exhaust to create a kind of hanger. You then use the shorter bolt supplied to bolt the 'hanger' to itself around the exhaust and the longer of the bolts is used to bolt the hanger to the swing arm.
Bending the plate is a bit of a pain in the arse and it took me a fair few attempts until I got it into the right shape. The fitting instructions could do with a diagram. I also scratched the paint of the exhaust a fair bit in the process of bending the plate (Tasso are aware of this issue).
The longer bolt to attach the hanger to the swing arm is a smaller diameter than the hole in the swing arm. Some people would be happy with this but back in the day I used a thinner bolt to attach an exhaust to my old 2t and it ended up wearing it's way through the swing arm.
I decided to drill out the hole in the hanger and use a standard size swing arm bolt and nut that I had spare.
In the end I gave up on all the bending and Tasso sent me a pre-bent strip of metal which made life much easier.
I know they are looking into alternative ways of supporting the exhaust at the swing arm.
The tricky part with fitting the exhaust is there are a lot of variables. The position on the hanger on the pipe,the angle the tail pipe point (up/down),how far the curved tail pipe is pushed on to the down pipe,which side of the swing arm the hanger sits,the angle of the down pipe from manifold. Tou also have to insure the tail pipe clears both rear and spare tyre (which it does if angles correctly).
This means the pipe doesn't just bolt on it more a case of bolt on,adjust,adjust,adjust.
Tasso have designed the pipe this way so that users can configure it how they want it but in my opinion people would much rather have a one piece pipe with welded bracket that was quick,simple and easy to fit. They have taken this on board.
My test ride was cut short because when I pulled over to check everything was ok I noticed the tail pipe had dropped a fair amount and was pointing down towards the road. I pulled it back up again and road home (over about 4 speed bumps) and when I got home the pipe had dropped again.
The tail pipe on the 200 model is a fair bit longer than the 125/150 model which means there is a fair bit of unsupported weight/twisting force at the tail end of the pipe. I am not sure if the U bolt is enough to stop this 'droopage'. I reported this back to Tasso and hopefully the new 'hanger' will solve this issue.
-Sound.
Tasso have been experimenting a lot to get the sound right and all the experimenting has paid off.
The pipe sounds meaty without being stupidly loud. You could happily ride down a residential street late at night without pissing the neighbours off too much but when you open the throttle it growls !
Performance-
There was no obvious performance boost from the exhaust although it seem to vibrate a lot less than a standard exhaust. I will be booking the scoot in at a dyno to get some science based numbers at some point in the future.
My scooter has a ram air filter fitted with a 95 main jet which to me felt spot on.
Summary-
It's a solid feeling,cheap to buy alternative to the other exhaust for the 4t on the market. The general 'brief' Tasso were working to was to create an exhaust that won't fall apart every six months,that sounds good and performs better than standard.
I think they have managed this and the price is fantastic but I do think there are a few little design problems that need ironing out.
If you have never fitted a scooter exhaust before then get someone who has to help you because this one is a little tricky.
For now I have re-fitted my standard exhaust. My scooter is my soul method of transport and I use it every day so I can't risk having something work loose while I am heading to do my weekly shop.
Luckily Tasso are being very proactive and improving the design based on customer feedback so it won't be long before they get it perfect.
(This review is based on my personal experience,other peoples experiences may differ)
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
Hope they're willing to send the new hanger international post!
I don't love the U-bolt. I may have something machined.
Honestly, stock performance would be fine by me. I just need a sturdier exhaust than stock.
I don't love the U-bolt. I may have something machined.
Honestly, stock performance would be fine by me. I just need a sturdier exhaust than stock.
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
-
- Member
- Posts: 214
- Joined: Fri Aug 17, 2012 12:25 pm
Sturdier than stock was what they were aiming for when they developed it and yeh I agree the mounting hardware really does let it down.ericalm wrote:Hope they're willing to send the new hanger international post!
I don't love the U-bolt. I may have something machined.
Honestly, stock performance would be fine by me. I just need a sturdier exhaust than stock.
I am thinking about modifying a stock exhaust,removing the cats,strengthening the swing arm bracket and finding a way of making it less likely to rust every time it goes near water.
- TheFatBlackWasp
- Member
- Posts: 2
- Joined: Sun Jun 29, 2014 2:41 pm
Rejetting info on a stock carb?
Is this re-jetting information based on a stock carburetor? I'm about to do the upgrades you just described--the ram air filter with the Tasso exhaust and wanted to go ahead and get the jetting done right away.ericalm wrote:Hope they're willing to send the new hanger international post!
I don't love the U-bolt. I may have something machined.
Honestly, stock performance would be fine by me. I just need a sturdier exhaust than stock.
-
- Member
- Posts: 4
- Joined: Sun Mar 02, 2014 9:47 pm
- Location: Hollywood, FL
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
Re: Rejetting info on a stock carb?
Yup, stock carb..TheFatBlackWasp wrote:Is this re-jetting information based on a stock carburetor? I'm about to do the upgrades you just described--the ram air filter with the Tasso exhaust and wanted to go ahead and get the jetting done right away.ericalm wrote:Hope they're willing to send the new hanger international post!
I don't love the U-bolt. I may have something machined.
Honestly, stock performance would be fine by me. I just need a sturdier exhaust than stock.
Tried the 95 main and 42 pilot. I need to check the plug and put in the new air filter, but I suspect it's not getting enough air. It starts to sputter at WOT in the lower gears. Trial and error. Very easy to swap; easier than getting to the fraggin' dabpdnabbit air filter. Hopefully get back in it tomorrow night.
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
-
- Member
- Posts: 214
- Joined: Fri Aug 17, 2012 12:25 pm
I think I would go for the GPR if it was available for the 200 because I prefer how it looks and the quality seems better.Spemoni wrote:I have 500 miles on my 2013 Stella with a sidecar.
I'm torn between the Tasso RIP and the GPR LML.2FUAO.MCP239.
Both will cost me virtually the same.
From what I've read, up-jetting will be the same for either exhaust also.
Has anyone compared these two exhausts????
- Neurotic-Hapi-Snak
- Member
- Posts: 335
- Joined: Thu Jun 05, 2014 2:56 am
I'm surprised they don't. Is the 200 not as popular? I know Britain has a two tier mc license system (under 125cc/over 125cc), but do other parts of Europe, making the 125/150 more popular?Tipper wrote:I think I would go for the GPR if it was available for the 200 because I prefer how it looks and the quality seems better.Spemoni wrote:I have 500 miles on my 2013 Stella with a sidecar.
I'm torn between the Tasso RIP and the GPR LML.2FUAO.MCP239.
Both will cost me virtually the same.
From what I've read, up-jetting will be the same for either exhaust also.
Has anyone compared these two exhausts????
Also, I just bought the GPR exhaust, was going to buy it off of Ebay but the seller removed the listing. Then I found it on Amazon from the same seller, but cheaper ($241 shipped vs $299 shipped). Hopefully Italian airplanes are as fast as their cars and scooters, lol.
Eric, does it stall/hesitate when you open the throttle to WOT quickly or does it sputter/die/misfire when at WOT?
-
- Member
- Posts: 214
- Joined: Fri Aug 17, 2012 12:25 pm
I spoke to GPR about it and they said that they havent been able to get hold of 200 to use while developing the exhaust.
I tried finding someone on the Italian forum who was willing to lend GPR their scooter but didnt have any luck.
As far as I know the 200 4t is now the best selling LML model in Europe although I think the Auto with soon take over.
I tried finding someone on the Italian forum who was willing to lend GPR their scooter but didnt have any luck.
As far as I know the 200 4t is now the best selling LML model in Europe although I think the Auto with soon take over.
- Neurotic-Hapi-Snak
- Member
- Posts: 335
- Joined: Thu Jun 05, 2014 2:56 am
I wish the 200 was sold over here, but Genuine isn't willing to pay the money to get it EPA certified. So I bought a 150. Already planning on the Polini 165cc cylinder, maybe swap out the gearing to the 2T/EFL gearing. Tomorrow, I'm going to take off the intake manifold and smooth the inside, might net me a little boost, especially at high RPM, by reducing intake turbulence.Tipper wrote:I spoke to GPR about it and they said that they havent been able to get hold of 200 to use while developing the exhaust.
I tried finding someone on the Italian forum who was willing to lend GPR their scooter but didnt have any luck.
As far as I know the 200 4t is now the best selling LML model in Europe although I think the Auto with soon take over.
The reasons I chose the GPR over the Tasso or Polini, was stainless steel/aluminum vs powder coated steel, and that the GPR doesn't require disassembly to change the rear tire.
-
- Member
- Posts: 162
- Joined: Thu Apr 18, 2013 5:19 am
- Location: Vista CA (San Diego)
- Contact:
I bit the bullet and ordered one of these yesterday. I'll probably start a new thread when I install it so others can learn from and avoid my mistakesNeurotic-Hapi-Snak wrote:...I wish the 200 was sold over here, but Genuine isn't willing to pay the money to get it EPA certified. So I bought a 150. Already planning on the Polini 165cc cylinder....
- Neurotic-Hapi-Snak
- Member
- Posts: 335
- Joined: Thu Jun 05, 2014 2:56 am
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
Just sputtering at sustained WOT in lower gears. But… I got rid of it.Neurotic-Hapi-Snak wrote:Eric, does it stall/hesitate when you open the throttle to WOT quickly or does it sputter/die/misfire when at WOT?
Seems like it, yeah.Neurotic-Hapi-Snak wrote:So Eric, is the RAM air filter that replaces the stock worth it? Does it seem to have a higher flow than the stock?
I installed the Ram, richened the air/fuel mix, and it's running much more smoothly now. No sputtering, a little pop on occasion when I decelerate. Performance has picked up, too.
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
- matto
- Member
- Posts: 11
- Joined: Mon Apr 22, 2013 12:54 am
- Location: Dallas, Texas
- Neurotic-Hapi-Snak
- Member
- Posts: 335
- Joined: Thu Jun 05, 2014 2:56 am
- ericalm
- Site Admin
- Posts: 16842
- Joined: Sat Jun 10, 2006 3:01 am
- Location: Los Angeles, CA
- Contact:
I got two sizes up in each jet and went straight for the largest ones. I'm going to dial back the main to the 95 and see how it does. Running pretty rich now.
Eric // LA Scooter Meetup Group // Stella 4T // Vespa LX // Vespa LXS // Honda Helix // some, uh, projects…
- Neurotic-Hapi-Snak
- Member
- Posts: 335
- Joined: Thu Jun 05, 2014 2:56 am
-
- Member
- Posts: 214
- Joined: Fri Aug 17, 2012 12:25 pm
-
- Member
- Posts: 660
- Joined: Sun Jan 15, 2012 2:55 am
- Location: kansas city mo
Popping on deceleration is usually an over rich idle setting. What is your mixture screw setting? IMHO you don't need to upjet the pilot jet( sometimes called idle jet) unless you've changed the engine internally or switched to An open air filter.
I would imagine a jet of 2-4 points up being the maximum needed with some bikes needing no up jetting at all. I have a friend with a chetak and a poc pipe. He down jetted and it's the best running bajaj I've ever encountered.
I would imagine a jet of 2-4 points up being the maximum needed with some bikes needing no up jetting at all. I have a friend with a chetak and a poc pipe. He down jetted and it's the best running bajaj I've ever encountered.
161cc big bore kit, NCY big valve head Hand ported, NCY transmission kit, jetted and tuned. I can port your cylinder head.
- matto
- Member
- Posts: 11
- Joined: Mon Apr 22, 2013 12:54 am
- Location: Dallas, Texas
I left the Pilot Jet alone, however, I did upjet the main from 90 to 95. My air mixture screw was set at about 1 1/2 turns. After several test runs I was able to determine that the addition of the ram air filter and tasso exhaust had added enough air to require 1 turn. I am now back up to 60 mph instead of 55.
There is still quite a bit of pop on the deceleration which does indicate a rich mixture, but I kind of like it
There is still quite a bit of pop on the deceleration which does indicate a rich mixture, but I kind of like it
- Cangurito
- Member
- Posts: 10
- Joined: Sat May 16, 2015 10:36 am
- Location: Spain
Hello Ericalm,
I have read in the post regarding "idle jet N424-74C spare is incorrect" that you were running rich and decided to go back to the stock idle jet (size 40 with 6 holes). My question is ..was the spare idle jet an 8 holes (was size 42?)
Neurotic-Hapi-Snak reported in the topic this could be probably the reason because he was running rich and it became hard to get the carburettor well tunned.
Can you share with us some news about the state of your current tunning, how it is configured (Main jet, Idle jet, straight air filter or modified stock filter, exhaust was Tasso?) and how it is working?
I would like to upgrade with GPR exhaust with re-jetting of the stock carb and mod of the air filter too, but i would like to know if someone else experienced same problems with those spare idle jets with 8 holes.
Any help is highly appreciated,
Saludos.
I have read in the post regarding "idle jet N424-74C spare is incorrect" that you were running rich and decided to go back to the stock idle jet (size 40 with 6 holes). My question is ..was the spare idle jet an 8 holes (was size 42?)
Neurotic-Hapi-Snak reported in the topic this could be probably the reason because he was running rich and it became hard to get the carburettor well tunned.
Can you share with us some news about the state of your current tunning, how it is configured (Main jet, Idle jet, straight air filter or modified stock filter, exhaust was Tasso?) and how it is working?
I would like to upgrade with GPR exhaust with re-jetting of the stock carb and mod of the air filter too, but i would like to know if someone else experienced same problems with those spare idle jets with 8 holes.
Any help is highly appreciated,
Saludos.