how setup new carb

Discussion of the Genuine Buddy, Hooligan, Black Jack and other topics, both scooter related and not

Moderator: Modern Buddy Staff

Post Reply
paulmars
Member
Posts: 19
Joined: Thu Aug 01, 2019 5:54 pm

how setup new carb

Post by paulmars »

just got new goodfit PD18 carb and set screws and hoses different then stock carb.

wolf RX-50, 49cc engine

see pics.

A adj is ?

B adj is ? and its only on the new carb, not on the old, why?

C hose drain

D hose fuel in

E hose ? and its only on the new carb, not on the old, why?

any ideas?

2nd pic old carb

pics: https://advrider.com/f/threads/how-setu ... b.1400162/

tks,
paul
User avatar
Stanza
Member
Posts: 575
Joined: Mon Jan 29, 2018 8:34 pm
Location: Chicago

Post by Stanza »

Paul, please bear in mind, this is a forum dedicated to the Genuine brand of scooters. Not wolf. None of the genuine bikes use a QMB engine, which yours has. This is like coming to a sandwich shop and asking what the recipe is for cherry pie.
paulmars
Member
Posts: 19
Joined: Thu Aug 01, 2019 5:54 pm

Post by paulmars »

And someone there might just hav the recipe.
User avatar
buzzvert
Member
Posts: 150
Joined: Sun Jul 28, 2019 11:44 pm
Location: Longmont, CO

Post by buzzvert »

Ingredients
4 cups fresh or frozen tart cherries
1 to 1 1/2 cups granulated sugar
4 tablespoons cornstarch
1/8 tablespoon almond extract (optional)
Your favorite pie crust or pie dough recipe for 2 crust pie
1 1/2 tablespoons butter, to dot
1 tablespoon granulated sugar, to sprinkle

Place cherries in medium saucepan and place over heat. Cover. After the cherries lose considerable juice, which may take a few minutes, remove from heat. In a small bowl, mix the sugar and cornstarch together. Pour this mixture into the hot cherries and mix well. Add the almond extract, if desired, and mix. Return the mixture to the stove and cook over low heat until thickened, stirring frequently. Remove from the heat and let cool. If the filling is too thick, add a little water, too thin, add a little more cornstarch.
Preheat the oven to 375 degrees F.

Use your favorite pie dough recipe. Prepare your crust. Divide in half. Roll out each piece large enough to fit into an 8 to 9-inch pan. Pour cooled cherry mixture into the crust. Dot with butter. Moisten edge of bottom crust. Place top crust on and flute the edge of the pie. Make a slit in the middle of the crust for steam to escape. Sprinkle with sugar.

Bake for about 50 minutes. Remove from the oven and place on a rack to cool.
Alzero
Member
Posts: 55
Joined: Wed Apr 10, 2019 8:27 pm
Location: East coast waters

Post by Alzero »

Try chinariders.net....,
User avatar
babblefish
Member
Posts: 3118
Joined: Tue Dec 04, 2007 8:42 am
Location: San Francisco

Re: how setup new carb

Post by babblefish »

paulmars wrote:just got new goodfit PD18 carb and set screws and hoses different then stock carb.

wolf RX-50, 49cc engine

see pics.

A adj is ?

B adj is ? and its only on the new carb, not on the old, why?

C hose drain

D hose fuel in

E hose ? and its only on the new carb, not on the old, why?

any ideas?

2nd pic old carb

pics: https://advrider.com/f/threads/how-setu ... b.1400162/

tks,
paul
A fuel bowl drain screw

B idle air/fuel adjustment screw. This is hidden behind a plug on US original equipment carbs. You ID'd it correctly on the old carb. Leave it alone for the moment.

C fuel drain and overflow tube

D fuel line

E air vent for fuel bowl. It's not allowed on American original equipment market vehicles because of emission requirements - your old carb probably ducts that elsewhere. It's OK to leave as is on the new one.

I'm not smart. I just copied and pasted from that website you posted.:)
Some people can break a crowbar in a sandbox.
paulmars
Member
Posts: 19
Joined: Thu Aug 01, 2019 5:54 pm

Post by paulmars »

A is tight
User avatar
babblefish
Member
Posts: 3118
Joined: Tue Dec 04, 2007 8:42 am
Location: San Francisco

Post by babblefish »

paulmars wrote:A is tight
They usually are. Many people change from the standard phillips (crosshead) screws to allen head for easier disassembly in the future.
Some people can break a crowbar in a sandbox.
Post Reply