Forums
 FAQHelp  LinksLinks    SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

DR177 kit installation

 
Post new topic   Reply to topic    Forums » Stella Discussion Previous topic :: Next topic  
Author Message
Mr.FixIt
Member


Joined: 01 Aug 2018
Posts: 112
Location: York, PA, USA
Stella 2T

PostPosted: Sat Sep 14, 2019 2:35 pm    Post subject: DR177 kit installation Reply with quote

Might as well start a new thread on this.

DR177 kit from Scooter Mercato came in Thursday. I spend all evening doing the cleaning and prep work to bolt the kit in. No grinding, no cutting, just bolt on. I remembered to measure how much stud was sticking up above the head joint, so I just threaded them back in the same distance and used the torque wrench to finalize the installation. Added enough 2T oil to the fuel tank for an extra pre-mix for run-in.

I managed to sleep all night with anticipation of kicking her back to life this morning.

It was that easy after I re-attached the SITO+ exhaust. I dropped in the 112 Main Jet to start with. She fired up with a nice bit of smoke from all the assembly lubrication. A quick twiddle on the idle mix screw and she's idling nicely. I triple-checked the timing.

I would have been alarmed at the noise from the new cylinder, but I watched a few videos where others experienced the same thing, and they said that the DR kit is just loud at first and will eventually seat in.

I wanted to go down to the post office, but it started raining so I didn't get a test drive in yet.

More to come when I get a few miles on...

_________________
Eric
(aka Mr. Fix It)
Back to top
View user's profile Send private message  
johnk
Member


Joined: 03 Sep 2018
Posts: 167

2003 Stella 2T & 2012 Stella 4T

PostPosted: Sat Sep 14, 2019 2:52 pm    Post subject: Reply with quote

Nice work! I am really glad you got it working again.

I also like that the kit is "for agonistic purposes only."
Back to top
View user's profile Send private message  
2003stellaDave
Member


Joined: 30 May 2017
Posts: 53


PostPosted: Sat Sep 14, 2019 8:58 pm    Post subject: Reply with quote

Cool. Keep us posted!
Back to top
View user's profile Send private message  
Mr.FixIt
Member


Joined: 01 Aug 2018
Posts: 112
Location: York, PA, USA
Stella 2T

PostPosted: Sat Sep 14, 2019 10:52 pm    Post subject: Reply with quote

Well, gang.... the rain finally stopped enough to do additional testing.

The 112 main jet was silly rich. It was just soot on the plug.

I skipped over 110 and went straight to 108. Still sooty.

I went down to 106 with a hint of soot, but not a lot of go. It burbled like it was too rich.

I didn't expect to go less than that initially, so I was faced with a quandary. I didn't want to jump the whole way back to a 100 main with nothing in the middle to tune with. So the only thing to do was increase the air. (I'm able to strip the main jet out with my eyes closed at this point)

I "de-blued" the stock air cleaner and discovered it was fairly contaminated with oil in the white part too. So I cut all of it off. (its an adventure right?) I had plenty of UNI air filter foam in stock, so that was fitted to the air filter frame.

Now with a free breathing air cleaner the 106 main jet hesitates ever so slightly like its too rich, confirmed by a hint of soot on the plug on a short ride. So I threw the 100 main back in and went around the neighborhood. With the free-flowing air filter, it seemed about right. Its still in break-in so I can't hit the revs and see how she pulls. It putters around reasonably, with only a hint of soot. The problem is running 3% oil for break-in contributes to an oily plug. I haven't gone for more than a mile or so on each of the final test rides, so she's really not up to temperature.

I'm certainly not going to call it a final tune. I might not even attempt "final tune" till I get a couple hundred miles into break in. Its close enough for today and I need a beer. For "agnostic purposes only", I think I'll just be skeptical enough to believe that it needs more testing and tuning. Razz

_________________
Eric
(aka Mr. Fix It)
Back to top
View user's profile Send private message  
Mr.FixIt
Member


Joined: 01 Aug 2018
Posts: 112
Location: York, PA, USA
Stella 2T

PostPosted: Fri Sep 20, 2019 7:50 pm    Post subject: Reply with quote

Update.

The ride and tune testing continues on the DR177 & Sito+. As of today the present jetting is:

Stock 20/20 carb
55/160 idle, 160 air, BE3 atomizer and a 106 main jet.


4th gear and a good bit of throttle is just about right. Its still not broken in yet, so its not really peppy. I can cruise easily at 35-40mph on the flat. The 108 main jet was just boggy and wouldn't go.

Here's the issue. Part throttle just tootling down the road it has a burble to it. I don't know how to describe it. It hesitates and is not smooth. As soon as I add more throttle and she starts to pull it smooths out. Pulling the choke strangles the engine so its still not too lean.

Now I'm not sure what to change to get the mid-range corrected. Confused

_________________
Eric
(aka Mr. Fix It)
Back to top
View user's profile Send private message  
Christopher
Member


Joined: 11 Nov 2019
Posts: 8
Location: Rochester Minnesota
2007 Stella 150

PostPosted: Mon Nov 11, 2019 11:40 am    Post subject: Reply with quote

Did you ever get the jetting figured out? Curious what you ended up with. I just bought a Stella with the same setup.
Back to top
View user's profile Send private message  
Mr.FixIt
Member


Joined: 01 Aug 2018
Posts: 112
Location: York, PA, USA
Stella 2T

PostPosted: Mon Nov 11, 2019 12:40 pm    Post subject: Reply with quote

The weather turned cold, so I haven't come to a final conclusion with enough miles for break in. It is between 106 and 108 Main Jet.

The 106 gives good pickup and pulling torque, but hasn't yielded a brown plug color. It does bog down when I pull the choke, so not overly lean.

The 108 seem a bit doggy in general like it is too rich. I'm considering a 107 Main Jet. If I drive by the Cylinder Head Temperature gauge, I can reach 280'F without really pushing hard (with this cold weather). That's making me think it might still be a little on the lean side, OR its still tight and not broken in properly.

_________________
Eric
(aka Mr. Fix It)
Back to top
View user's profile Send private message  
Christopher
Member


Joined: 11 Nov 2019
Posts: 8
Location: Rochester Minnesota
2007 Stella 150

PostPosted: Wed Nov 13, 2019 2:28 am    Post subject: Reply with quote

I want to try one of these, should be able to get a really good idea of the jetting for each stage.

https://www.plxdevices.com/PLX-Wideband-O2-Air-Fuel-Ratio-Sensor-Modules-Gauges-s/125.htm
Back to top
View user's profile Send private message  
Mr.FixIt
Member


Joined: 01 Aug 2018
Posts: 112
Location: York, PA, USA
Stella 2T

PostPosted: Wed Nov 13, 2019 7:21 pm    Post subject: Reply with quote

Its nice to be able to put a number on something and chart it out. The wide-band lambda sensors are power-hungry to keep the internal heater warm. I bought a system like this 15 years ago to try to measure the emissions of a natural gas Caterpillar G3406 engine that I was working on. The results were less than exciting. I ended up not using it, and it was an expensive failed experiment.

That's not to say that this newer unit wouldn't work. I imagine it would require fairly steady-state conditions to get a good measurement.

_________________
Eric
(aka Mr. Fix It)
Back to top
View user's profile Send private message  
Christopher
Member


Joined: 11 Nov 2019
Posts: 8
Location: Rochester Minnesota
2007 Stella 150

PostPosted: Thu Nov 14, 2019 12:22 am    Post subject: Reply with quote

I was thinking about feeding it with its own battery while tuning. Also need to hook up an.oscilloscope and see.how noisy the power really is. I could add a capacitor as a filter to the positive lead if needed.
Back to top
View user's profile Send private message  
Mr.FixIt
Member


Joined: 01 Aug 2018
Posts: 112
Location: York, PA, USA
Stella 2T

PostPosted: Tue Nov 19, 2019 5:04 pm    Post subject: Reply with quote

The #108 main jet was totally dogging on me last night when I took her out to the gas station for some Ethanol-Free. She didn't want to climb any hills. I put the #106 main jet back in which yields about the right performance.

So how hot should I let the CHT reading get (measured with the ring under the spark plug)? What's a good alarm threshold? Am I playing with fire exceeding 280°F and not really pushing it?

(edit)
According to http://www.vespalabs.org/wiki/vespa-tuning/gadgets/cylinder-head-temperature-gauge
Quote:
Roughly a Vespa engine will run at between 320F and 380F, different engine set-ups will run different temperatures



Apparently I have to re-torque the case bolts again, she's dripping gearbox oil. (grumble grumble)

_________________
Eric
(aka Mr. Fix It)
Back to top
View user's profile Send private message  
Christopher
Member


Joined: 11 Nov 2019
Posts: 8
Location: Rochester Minnesota
2007 Stella 150

PostPosted: Wed Nov 20, 2019 2:01 am    Post subject: Reply with quote

Those temperatures are about right, from my studying. I have been working on tuning my 50cc scooter with a 70cc big bore kit that turns 11,000 RPM. I've been using a cht gauge and shooting for around 320, I read to stop at 350.

This is where I get my information from.

http://49ccscoot.proboards.com
Back to top
View user's profile Send private message  
Mr.FixIt
Member


Joined: 01 Aug 2018
Posts: 112
Location: York, PA, USA
Stella 2T

PostPosted: Fri Dec 13, 2019 12:15 pm    Post subject: Reply with quote

Suffering from PMS (Parked Motorcycle Syndrome) as it is presently snowing.
I'm sitting here reflecting on the engine rebuild. I very much want to get out and get her broken in properly.

-------------------------------------

Night Flight

A red scooter is the best way to get around,
No other transport is finer that I have found.
A tank full of fuel will take you so far,
To visit with friends or hang at the bar.
After a dinner, its homeward we go,
Travel is pleasant its like we're on show.
Engine burble turns heads, like they've never seen,
So beautiful a cherished painted art scene.
My Italian-descended tibutation in style,
Nothing of late could bring such a smile.
A pinging was heard; whatever to do?
A loss of compression would surely ensue!
Darkness it came and I filled with dread.
It wasn't far to get back to the shed.
Coaxed up the hill giving all that she could,
The crest was ahead; I felt that we would.
Then plunged into darkness; nothing to see,
But a green lamp on the dash shining at me.
Off with the key and in with the clutch,
If I hit a tree, I'm sure it'd hurt much.
The whispers of wind was all that was heard,
The engine had died, and I uttered a word.
Word of complaint ruined my ride,
The headlamp was out! I could'a cried.
Some short distance more under the tree,
The moonlight provided little to see.
No push was needed; she showed such pride,
And that was the end of our valiant ride.

_________________
Eric
(aka Mr. Fix It)
Back to top
View user's profile Send private message  
Mr.FixIt
Member


Joined: 01 Aug 2018
Posts: 112
Location: York, PA, USA
Stella 2T

PostPosted: Sun Dec 22, 2019 8:31 pm    Post subject: Reply with quote

It was 45 degrees in the sun today, so I got Stella out for some more miles and testing.

Even though the CHT reads some reasonable numbers (at these cool ambient temperatures), I'm still paranoid about the mixture. Here's the test I did today.

I ran out on a straight flat road in 4th gear and then pulled the choke out.
The engine neither improved nor faltered. So is this enough evidence to tell me that its still running slightly lean?

_________________
Eric
(aka Mr. Fix It)
Back to top
View user's profile Send private message  
Mr.FixIt
Member


Joined: 01 Aug 2018
Posts: 112
Location: York, PA, USA
Stella 2T

PostPosted: Tue Dec 31, 2019 7:45 pm    Post subject: Reply with quote

The 107 main jet was installed this morning. The results are noticeable directly in cylinder head temperature. On the usual test run route at temperatures in the 40's the CHT did not rise significantly. The worry was that with the 106 Main Jet that the CHT rose far too quickly and high with cold ambient temperatures.

The engine is still in break-in, so I can't expect full power.

Pulling the plug was not overly sooty. The 107 looks like a keeper so far.

_________________
Eric
(aka Mr. Fix It)
Back to top
View user's profile Send private message  
Patchik
Member


Joined: 17 Feb 2020
Posts: 3
Location: Madison, WI
Stella 2T

PostPosted: Mon Feb 17, 2020 4:23 am    Post subject: Reply with quote

Hello! I have similar setup on my 2009 Stella, bolt-on DR 177 from Mercato and the stock 20/20 carb, but with an SIP Road exhaust. Probably only 1000 miles since it was all put together. (No speedo hence no odo) But it has broken in by now.

Been trying all sorts of jetting setups over the summer and settled at 107/BE3/160 main with 38/120 idle jet. Anything above 107 felt like I was four stroking when holding the throttle steady, just smacking way too loud while cruising at 30 which cleaned up when opening the throttle.

The 55/160 idle caused me so many woes though. Never ran ok with that idle jet.

I ended up using a Euro air filter with the drilled holes, but then plugged the oval air hole that feeds the under the throttle slide. Paranoid about seizing when letting off the throttle at WOT I suppose. Heard Stellas have a lean throttle slide that provides extra air in the mid range for emissions or something.

Now I feel like I did something way too complicated, but I'm curious to see what works for yours. Mine seems accidentally perfect! But I'm swapping the carb boxes to deal with the 2T oil leaks so will re-test the jetting in a month.

Here for the examples for jetting the Stella with a 20/20 carb and a bolt on DR 177. Best of luck. May the winter break soon!


Last edited by Patchik on Mon Feb 17, 2020 6:57 pm; edited 1 time in total
Back to top
View user's profile Send private message  
Mr.FixIt
Member


Joined: 01 Aug 2018
Posts: 112
Location: York, PA, USA
Stella 2T

PostPosted: Mon Feb 17, 2020 1:25 pm    Post subject: Reply with quote

That's what I need, a break in the weather. All the testing has been done at uncomfortably cold temperatures.

Patchik, thank you for sharing your experience with the idle jet. Its worth the effort to try a change there. I too have experienced issues with mid-range throttle with testing so far.

_________________
Eric
(aka Mr. Fix It)
Back to top
View user's profile Send private message  
Christopher
Member


Joined: 11 Nov 2019
Posts: 8
Location: Rochester Minnesota
2007 Stella 150

PostPosted: Mon Feb 17, 2020 1:55 pm    Post subject: Reply with quote

Patchik wrote:
Hello! I have similar setup on my 2009 Stella, bolt-on DR 177 from Mercato and the stock 20/20 carb, but with an SIP Road exhaust. Probably only 1000 miles since it was all put together. (No speedo hence no odo) But it has broken in by now.

Been trying all sorts of jetting setups over the summer and settled at 107/BE3/160 main with 32/120 idle jet. Anything above 107 felt like I was four stroking when holding the throttle steady, just smacking way too loud while cruising at 30 which cleaned up when opening the throttle.

The 55/160 idle caused me so many woes though. Never ran ok with that idle jet.

I ended up using a Euro air filter with the drilled holes, but then plugged the oval air hole that feeds the under the throttle slide. Paranoid about seizing when letting off the throttle at WOT I suppose. Heard Stellas have a lean throttle slide that provides extra air in the mid range for emissions or something.

Now I feel like I did something way too complicated, but I'm curious to see what works for yours. Mine seems accidentally perfect! But I'm swapping the carb boxes to deal with the 2T oil leaks so will re-test the jetting in a month.

Here for the examples for jetting the Stella with a 20/20 carb and a bolt on DR 177. Best of luck. May the winter break soon!


You can get slides with no holes and no cut outs on the bottom side from SIP scooter. I bought one and am waiting for warmer weather also. I figure a blank slate on the slide with the changes made won't be a bad thing.
Back to top
View user's profile Send private message  
Patchik
Member


Joined: 17 Feb 2020
Posts: 3
Location: Madison, WI
Stella 2T

PostPosted: Mon Feb 17, 2020 6:58 pm    Post subject: Reply with quote

Edit to my previous post, I'm using a 38/120 idle jet.
Back to top
View user's profile Send private message  
Mr.FixIt
Member


Joined: 01 Aug 2018
Posts: 112
Location: York, PA, USA
Stella 2T

PostPosted: Tue Feb 18, 2020 1:17 pm    Post subject: Reply with quote

Hopefully shifting the mid-range to the leaner side through the idle jet and enriching the main jet back to 107 makes the difference. It certainly feels too rich in part-throttle as it is. If the SIP Road Pipe is similar to the SITO+ there should be similar results. There are a few steps in between the two jets according to the list of available jets. I have bigger main jets in stock as well so there is room for experimentation. Thanks for sharing your experience, Patchik.
The testing will continue....
I feel as if I have a small fortune invested in jets. Wink

_________________
Eric
(aka Mr. Fix It)
Back to top
View user's profile Send private message  
Display posts from previous:   
Post new topic   Reply to topic    Forums » Stella Discussion Previous topic :: Next topic  Time: GMT

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

  Scootergear designed by riders for riders


Powered by phpBB © 2001, 2005 phpBB Group
All Content Copyright 2007-2011 by Modern Buddy. All Rights Reserved.