Flushing/Bleeding Front Brake Buddy 125

PistolPete7390 · Post by **PistolPete7390** » Mon Apr 16, 2018 6:13 pm

Looking for some direction on Flushing/Bleeding Front Brakes on my 2007 Buddy 125. Front break is feeling a little soft.

Is there already posts that people know of about doing so?

Looking for some steps for clarification so I don't screw it up.

Any input would be greatly appreciated. Thank you Everyone!

Happy Riding!

Point37 · Post by **Point37** » Mon Apr 16, 2018 6:17 pm

had to use a site specific search on google...way easier than the search function on here...

site:http://www.modernbuddy.com front brake bleeding

http://www.modernbuddy.com/forum/viewto ... kes#197608

DeeDee · Post by **DeeDee** » Mon Apr 16, 2018 11:08 pm

You can do it by yourself, but it is easier if you have a friend squeezing the lever. You have to remove the top part of the headset. Get a small clear hose to fit over the bleed nipple. Remove the reservoir cover, and drain out the old fluid w/ a turkey baster or syringe. Fill up close to the top. Have the tube on the nipple, and the other end in a clear bottle. Open the nipple 1/4 turn, squeeze, hold lever in. Tighten nipple, release lever. Repeat until new brake fluid comes out the end of the tube. You will have to refill the reservoir 2 or 3 times. Be careful not to let the reservoir run empty. Do not let out the lever if the nipple is open. Loads of YouTube videos showing how to do this. Once your done squeeze and release the lever a few times to build up pressure. Might as well check your pads why your at it.

DeeDee · Post by **DeeDee** » Tue Apr 17, 2018 12:39 am

Ace Hardware sells clear flexible tubing by the foot. Get yourself a 1/4-20 bolt. The bolt will slide into the diameter you need w/ a bit of friction. Buy 12 to 15" of it. Get the smallest brake fluid container you can buy. It only takes a few ounces.

RoaringTodd · Post by **RoaringTodd** » Tue Apr 17, 2018 11:37 am

How do you know when it is the new brake fluid, and not the old one?

DeeDee · Post by **DeeDee** » Tue Apr 17, 2018 11:58 am

You can tell by the color. That's where a clear tube and clear bottle help. Old fluid will be the color of dark honey. New fluid looks like vegetable oil.

PistolPete7390 · Post by **PistolPete7390** » Tue Apr 17, 2018 2:05 pm

DeeDee wrote:You can do it by yourself, but it is easier if you have a friend squeezing the lever. You have to remove the top part of the headset. Get a small clear hose to fit over the bleed nipple. Remove the reservoir cover, and drain out the old fluid w/ a turkey baster or syringe. Fill up close to the top. Have the tube on the nipple, and the other end in a clear bottle. Open the nipple 1/4 turn, squeeze, hold lever in. Tighten nipple, release lever. Repeat until new brake fluid comes out the end of the tube. You will have to refill the reservoir 2 or 3 times. Be careful not to let the reservoir run empty. Do not let out the lever if the nipple is open. Loads of YouTube videos showing how to do this. Once your done squeeze and release the lever a few times to build up pressure. Might as well check your pads why your at it.

Thank you DeeDee! Great information here! You actually assisted me in the finding of my 2007 Buddy 125 Italia a year ago from the Bronx. You sent the information to my brother and I went and bought it! My brother Matt bought a Orange 06 Buddy 125 off you in Denver! You're help and assistance is greatly appreciated! Thank you so much!