MRP 125 Exhaust
Posted: Tue Aug 28, 2007 1:15 am
though i have no experience with that particular pipe- MRP stuff is pretty good. joel wont just slap his name on anything.
it'd go on my bike.
Modern Buddy
The premier site for Genuine Buddy, Stella, Blur, Rattler, Roughouse and Black Cat scooters
https://www.modernbuddy.com/forum/
MRP 125 Exhaust
Page 1 of 1
Posted: Tue Aug 28, 2007 1:56 am
Posted: Tue Aug 28, 2007 2:39 am
That looks pretty sweet, what does it cost?
Posted: Tue Aug 28, 2007 2:46 am
That looks pretty sweet, what does it cost?
Not sure but I will try and give them a call tomorrow and post the details.
Not sure but I will try and give them a call tomorrow and post the details.
Posted: Tue Aug 28, 2007 3:14 am
MRP will only talk to dealers, I called them and the dude about hung up on me and stated they only sell to dealers. so I guess we have to find out who the dealers are and get a price from them.
Posted: Tue Aug 28, 2007 4:22 am
looks like scootertronics is selling it for $279.00
http://store.scootertronics.com/gebu125hipee.html
http://store.scootertronics.com/gebu125hipee.html
Posted: Tue Aug 28, 2007 10:41 pm
looks like scootertronics is selling it for $279.00
http://store.scootertronics.com/gebu125hipee.html
Nice find SCOOTER SOLDIER but after calling scootertronics they were less then helpful with any info so I called MRP and although they tried to deter me, persistence payed off and I was able to get through. I was told that this pipe would yield another 1.5 to 2 HP gain which I consider significant, approx a 20% increase. You would need to rejet the carb and can expect 5 mph additional top end with even more speed available by using Dr. Pulley rollers. Due to increased acceleration you can change the weight of the rollers to gain a little more top end without loosing any (before the pipe install) acceleration. Looks very promising.
http://store.scootertronics.com/gebu125hipee.html
Nice find SCOOTER SOLDIER but after calling scootertronics they were less then helpful with any info so I called MRP and although they tried to deter me, persistence payed off and I was able to get through. I was told that this pipe would yield another 1.5 to 2 HP gain which I consider significant, approx a 20% increase. You would need to rejet the carb and can expect 5 mph additional top end with even more speed available by using Dr. Pulley rollers. Due to increased acceleration you can change the weight of the rollers to gain a little more top end without loosing any (before the pipe install) acceleration. Looks very promising.
Posted: Wed Aug 29, 2007 12:33 am
Posted: Wed Aug 29, 2007 11:52 am
That's the pipe I will be getting next season.
Posted: Wed Aug 29, 2007 2:38 pm
impressive, I hae to admit I like the looks a little better than the prima, I would like to see the spec sheets side by side on these two pipes and see which is the better performance wise.
I noticed you mentioned Dr.pully roller weights, are those the roller weight of choice for the buddy or any scooter? when I replace mine I want the best roller weights in addition to a kevlar belt, I Just have to figure out if I want to stay at the same weight or increase top end just a tad.
I noticed you mentioned Dr.pully roller weights, are those the roller weight of choice for the buddy or any scooter? when I replace mine I want the best roller weights in addition to a kevlar belt, I Just have to figure out if I want to stay at the same weight or increase top end just a tad.
Posted: Fri Aug 31, 2007 4:39 pm
anyone have this pipe and have a picture of it on our beloved buddy 