OLIVE IS DEAD

jmkjr72 · Post by **jmkjr72** » Mon May 03, 2010 1:44 am

olive siezed up on me on my way to scout leader training camp on friday
i must have been too slow on the clutch as she high sided on me at 60 mph when she siezed up
well olive is home and in the garage
it is a hard seize situation ill have to tare her apart to see what is wrong
i think it might have been a crank failure but i wont know for sure till i get her apart
here are some pics of the damage

now onto the damage to me

please wear your gear you can see what happend to my ff helmet imgainge if that was my face and had hit the asphalt at 60
my jacket and pants took a beating too

BuddyRaton · Post by **BuddyRaton** » Mon May 03, 2010 10:35 am

Sorry to hear about this. Honestly...you look pretty good for hitting the road at that speed.

Were you running stock or modified?

loodieboy · Post by **loodieboy** » Mon May 03, 2010 11:16 am

Glad you're okay.

jmkjr72 · Post by **jmkjr72** » Mon May 03, 2010 11:19 am

pipe and carb are the only mods and i have had these on for over 1500 miles
i was running the injector +1% in the tank

Kaos · Post by **Kaos** » Mon May 03, 2010 2:18 pm

Yikes, that doesn't look like much fun. Hope you get you and your bike sorted quick!

polianarchy · Post by **polianarchy** » Mon May 03, 2010 5:11 pm

Whew! I'm glad you're relatively okeh, and I'm sorry about poor Olive. I hope y'all can work it out!

jmkjr72 · Post by **jmkjr72** » Mon May 03, 2010 8:44 pm

i started the autopsy and im psotive it was crank failure now
i pulled the head and was able to move the bore up some till it hit the body
there are some dings in the top of the piston and in the squish band

so im thinking it will be about 600 bucks in parts to get her back running
then throw in a fender new kick start trim and rework the cowel again

Rippinyarn · Post by **Rippinyarn** » Wed May 05, 2010 5:28 pm

Wow man, keep on healing up. Cranks bearings, do you think or a actual crank failure. Either way, melt that friggin' evil crank down into droplets to teach it a lesson.

Glad that you are OK and that your FF did it's job.

KRUSTYburger · Post by **KRUSTYburger** » Thu May 06, 2010 12:09 am

Man, I know you gotta be sore, glad to hear there were no major injuries! Good luck with the repairs.

bluezurich · Post by **bluezurich** » Thu May 06, 2010 12:15 am

Sorry to hear about your seize and partially hurt scoot. We are all glad you are well and able to post. it's the one's who crash and we don't hear from that really scare us.

I look forward to hearing of your progress and the restoration as well of Olive.

jmkjr72 · Post by **jmkjr72** » Thu May 06, 2010 12:52 am

i plan on making some sort of trophy out of the crank

i had to order a puller for the fly wheel
the one genuine sells to the dealers isnt very good i went by to have it pulled off and it just pulled the threads off the puller

BuddyRaton · Post by **BuddyRaton** » Thu May 06, 2010 8:37 pm

jmkjr72 wrote:i plan on making some sort of trophy out of the crank

Please keep us updated! Might as well change the bearings as long as your in there.

bluezurich · Post by **bluezurich** » Thu May 06, 2010 10:48 pm

If there are enough spare bad parts you could construct a little shrine for the side of the road where it occurred.

jmkjr72 · Post by **jmkjr72** » Fri May 07, 2010 12:27 am

i have a laundry list started bearings seals crank bbk

i have paint for the engine and rear hub i just have to get all that dam cosmoline off so i can paint it

i am waiting for my fly wheel puller to get in so i can make sure i order every thing i need in one shot

jmkjr72 · Post by **jmkjr72** » Sat Jun 19, 2010 12:10 am

well i know its been a while sense i updated this thread but i did the first heat cycle today on the rebuild

and she screams i hit 40 in second and had throttle left
i need to run a few heat cycles and do a proper plug chop before i can reall give her

but as she sits

i scrubed and painted the case and hub satin black

installed a mazz full circle crank

dr177 bbk (enlarged transfer ports raised the exhasut port about 1mm and widend exhasut port polished the exhaust head and piston)

mathced the case to the new huge transfer ports

ggr hot reeds with cross bar cut out of reed block

24/24 carb vsx air filter and carb box matched to the carb

somonine pipe

Carpediem · Post by **Carpediem** » Wed Jun 23, 2010 4:05 am

put up some new pics, like to see how far she's come.

jmkjr72 · Post by **jmkjr72** » Wed Jun 23, 2010 11:39 am

i havent done any more body work yet i did hammer out the dent in the cowel but i havent put filler on or figureed out what to do with the front fender

jmkjr72 · Post by **jmkjr72** » Mon Jun 28, 2010 1:21 am

i got sick of looking at that fubared front fender
so i got out my air grinder

and i painted the front hub
she is running good the temps staid good on the group ride yesterday but i was a bit dissapointed as olive wasnt the fastest scoot there we were joined by a bergman 400
so i had to settle for second fastest

ScootLemont · Post by **ScootLemont** » Mon Jun 28, 2010 2:18 am

How wast the ride yesterday?
Any pics?
Yvonne invited me to stick around... but I figured a group ride was not the best place to learn to shift

jmkjr72 · Post by **jmkjr72** » Mon Jun 28, 2010 2:29 am

it was good we had a fair turn out i think there was a dozen scoots
the bergman my stella another stella(sito + deblued and bj jetting) 3 rucks a buddy 125 a black cat(70 kit and prima pipe) and roughouse 2 etons(piped) and a kymco
but no one wanted to race and i couldnt hear if any one else was actauly running
i didnt take any pics forgot the good camera the guy on the bergman did have his camera with so hopefully there will be some pics posted some where
there wasnt much shifting on the ride we stuck in town just a few stop lights

ScootLemont · Post by **ScootLemont** » Mon Jun 28, 2010 2:41 am

I am sure it would have been fun... I should have stuck around.
I got the hang of the shifting thing pretty fast... maybe a few miles
I just thought it would take longer to get smooth - the idea of left handed grip shifting seems like such a weird idea... but, as you know, its no big deal