Buddy 125 exhaust gasket.....

giddyup98 · Post by **giddyup98** » Wed Jun 17, 2020 3:59 pm

Iâ€™m going to Be removing the exhaust on my Buddy 125 to replace the rear tire. Do I need a new exhaust gasket when I reattach the exhaust to the manifold or can I reuse the existing gasket? Thanks!

wheelbender6 · Post by **wheelbender6** » Wed Jun 17, 2020 5:06 pm

Not normally. Unless your Buddy is really old, you probably will not need a new gasket.

JettaKnight · Post by **JettaKnight** » Wed Jun 17, 2020 5:36 pm

giddyup98 wrote:Iâ€™m going to Be removing the exhaust on my Buddy 125 to replace the rear tire. Do I need a new exhaust gasket when I reattach the exhaust to the manifold or can I reuse the existing gasket? Thanks!

The answer will be obvious when you remove the existing one. If it's burnt up, then yes.

wheelbender6 wrote:Not normally. Unless your Buddy is really old, you probably will not need a new gasket.

Well, it looks like it's a 2009 model...

eggsalad · Post by **eggsalad** » Wed Jun 17, 2020 6:24 pm

Seems to me it's a "while you're in there" part. A new one is a couple of bucks.

giddyup98 · Post by **giddyup98** » Wed Jun 17, 2020 7:22 pm

Exhaust Gaskets ordered for both my Buddies. Gonna need to change the rear tire on my wifeâ€™s 170i soon.

Thanks for the advice everyone!

scootERIK · Post by **scootERIK** » Wed Jun 17, 2020 10:31 pm

I am pretty sure I put over 40,000 miles on one with no problems.

I know I have done over 20,000 on a few of them with no issues.

BayStateScooterist · Post by **BayStateScooterist** » Thu Jun 18, 2020 3:38 am

It all depends on how well the original exhaust gasket sits on the exhaust pipe indentation. When reinstalling the exhaust pipe after changing the tires on the Buddy 150 the original exhaust gasket didn't sit well in position, it moved a bit. Starting up the scooter resulted in a louder exhaust note. Ordering a new exhaust gasket (I bought 2) took care of the problem. The new exhaust gasket sat perfectly in position during exhaust re installation, resulting in the expected quieter exhaust note.

For now on. I will use a new exhaust gasket when reinstalling the exhaust pipe which is a pain to do.

giddyup98 · Post by **giddyup98** » Mon Jul 20, 2020 2:52 pm

I finally went to Reinstall the exhaust on my buddy 125 this morning, when I realized the original round crush gasket was different than the â€œconventionalâ€� style exhaust gasket that I received in the mail. Does this new style gasket replace the original round crush gasket? If so, do I have to remove the original gasket before using the new one?

giddyup98 · Post by **giddyup98** » Mon Jul 20, 2020 5:51 pm

Never mind. I got my answer from the vendor I bought them from.

If anyone wants to know, the new gasket is a much better replacement for the OEM round one.

Rdrett · Post by **Rdrett** » Tue Jul 21, 2020 4:46 am

giddyup98 wrote:Never mind. I got my answer from the vendor I bought them from.

If anyone wants to know, the new gasket is a much better replacement for the OEM round one.

Did you remove the original crush gasket?

giddyup98 · Post by **giddyup98** » Tue Jul 21, 2020 9:33 am

Yes, you donâ€™t need it with the new gasket.

BuddyRaton · Post by **BuddyRaton** » Fri Jul 24, 2020 9:03 pm

What one are you using?

Modern Buddy

Buddy 125 exhaust gasket.....

Buddy 125 exhaust gasket.....

Re: Buddy 125 exhaust gasket.....